Your donations help keep this valuable resource free and growing. Thank you.
|
MPFI |
Post Reply | Page 12> |
Author | |
AM XTASY
AMC Apprentice Joined: Oct/29/2010 Location: North Carolina Status: Offline Points: 245 |
Post Options
Thanks(0)
Posted: Jun/03/2023 at 3:17pm |
First total mock up with my MPFI Torker
|
|
wrebelmachine
AMC Apprentice Joined: Aug/08/2019 Location: SW Missouri Status: Offline Points: 162 |
Post Options
Thanks(0)
|
That looks nice and even on your set up. Keep us posted on results
|
|
mbwicz
Supporter of TheAMCForum Joined: Feb/20/2019 Location: Buffalo, NY Status: Offline Points: 2001 |
Post Options
Thanks(0)
|
Take some time and think about how you will be running your fuel lines and what regulator you will be using. On my car, I have the crossover setup in the front. My feed is on the driver side rear rail and the regulator is plugged into the rear of the passenger rail (edelbrock regulator). I had to add a clamp to get the crossover away from the thermostat housing.
I've also seen pics of a setup with 180 degree fittings plumbed the feed and return into the front of the rails and use a rear crossover. And figure out your throttle cable and return spring setup, since there is no boss to mount the factory bracket. Just a couple of thoughts before you get everything painted and finished! Mike
|
|
1970 AMX, one step forward, one step back. Both steps cost time and money.
|
|
JGRANTAMX
AMC Addicted Joined: Jun/02/2017 Location: Maine Status: Offline Points: 1703 |
Post Options
Thanks(0)
|
I created one before deciding to go boosted then changed to Edelbrock Pro Flow EFI.
J |
|
wrebelmachine
AMC Apprentice Joined: Aug/08/2019 Location: SW Missouri Status: Offline Points: 162 |
Post Options
Thanks(0)
|
Very nice!
|
|
AM XTASY
AMC Apprentice Joined: Oct/29/2010 Location: North Carolina Status: Offline Points: 245 |
Post Options
Thanks(0)
|
Ohh I already have got it all planned out in my head. I’ll be dead heading the system at the rails kind of how some new OEM crates are. So one regulated supply will be split rear of the motor to feed both rails, yeah the system has some draw backs with handling debris but it will allow for a cleaner install. As for the throttle cable mount, I’ll be 3D printing brackets to check fit before having them laser cut. Same with the rail tie ins.
|
|
AM XTASY
AMC Apprentice Joined: Oct/29/2010 Location: North Carolina Status: Offline Points: 245 |
Post Options
Thanks(0)
|
If it wasn’t for saving up for aluminum heads and working for a competitor to Edelbrock that probably would have been my route. Though making this intake has been a bit of fun.
|
|
AM XTASY
AMC Apprentice Joined: Oct/29/2010 Location: North Carolina Status: Offline Points: 245 |
Post Options
Thanks(1)
|
Took a break from modeling the rail hold downs and started playing with a valve cover crossover breather system. All tacked now I just gotta burn it together.
|
|
AM XTASY
AMC Apprentice Joined: Oct/29/2010 Location: North Carolina Status: Offline Points: 245 |
Post Options
Thanks(1)
|
Another closer look
|
|
i6cj7
AMC Apprentice Joined: Feb/20/2018 Location: virginia Status: Online Points: 140 |
Post Options
Thanks(0)
|
That. Is. NEAT.
|
|
Post Reply | Page 12> |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |