Your donations help keep this valuable resource free and growing. Thank you.
|
Prestolite Distributor replacement |
Post Reply | Page <12 |
Author | |
hillsidehemi
AMC Fan Joined: Jan/30/2015 Location: Stoughton WI Status: Offline Points: 6 |
Post Options
Thanks(0)
|
Odd ball 76 to I think 78 distributor. Nobody has them and all they offer is a rebuild service. Don't want to wait for that and I don't think it would fix my issues anyway.
|
|
hillsidehemi
AMC Fan Joined: Jan/30/2015 Location: Stoughton WI Status: Offline Points: 6 |
Post Options
Thanks(0)
|
Thanks for the replies and quick answers. I found a replacement vacuum can for the prestolite from a member here and I think that might fix my problem for the short term.
|
|
FSJunkie
AMC Addicted Joined: Jan/09/2011 Location: Flagstaff, AZ Status: Offline Points: 4742 |
Post Options
Thanks(0)
|
The path of least resistance is installing a replacement vacuum advance now that you have one.
Prestolite is not known for reliability, but my system has taken pretty good care of me in 50,000 miles of daily driving. Take care of the wires and connectors by keeping them clean, tight, and protected. Keep a spare module in the trunk. I've never had one outright die while driving, but I have had them develop hot idle misfires that signal that it's time to replace the module before it gets worse. I always had plenty of warning and replacing the module is a snap. I don't think updating to the 1978 to 1991 Duraspark II system is much of an upgrade. The Duraspark system was superior back in the day, and it has better parts support than Prestolite, but I've had absolutely terrible reliability from new replacement parts. So many were bad out of the box or failed within a year. It really soured my taste for that system. There is much to be said for Delco HEI. I think it's possibly the most reliable ignition system, ever. I worry about the qualiy and accuracy of new foreign-made HEI distributors, though. There are many cheapies out there. Points work too, but are high maintenance. You may or may not be fine with that. You don't need a ballast if you use a 3 ohm coil. Or, put a Pertronix module inside the points distributor. |
|
1955 Packard
1966 Marlin 1972 Wagoneer 1973 Ambassador 1977 Hornet 1982 Concord D/L 1984 Eagle Limited |
|
Mr_Roboto
AMC Apprentice Joined: Jun/12/2022 Location: Wisconsin Status: Offline Points: 221 |
Post Options
Thanks(0)
|
Another option to consider is doing a Duraspark Distributor. This may seem to be kind of pieced together, but it was actually a factory setup at a point. Get the cap/rotor/adapter/coil from an 83ish Ford 300. After that use a 4 pin HEI module an an external heat sink.
https://fordsix.com/ci/DSIIswap. - https://fordsix.com/ci/DSIIswap.html My Eagle is set up somewhat similarly, except the box is an MSD 6AL.
|
|
vinny
Supporter of TheAMCForum Joined: Jan/05/2012 Location: Calgary Status: Offline Points: 2837 |
Post Options
Thanks(0)
|
I have a spare 232 engine that had an old Prestolite distributor, not the one you guys are referring to. They are very reliable. A fellow that had a problem with the one you refer to asked for mine and I sent it to him. The defective distributor comes back with a surprise $50 bill under the cap. I pull the gear off it to put on the HEI that I had removed from a subsequently scrapped Chev 250. Good deals all around.
|
|
FuzzFace2
AMC Addicted Joined: Jul/05/2007 Location: Angier, N.C. Status: Offline Points: 10356 |
Post Options
Thanks(0)
|
Yes Ford after 75 used the DSII IGN system and they work pretty good just like the Prestolite till they fail.
I have a factory 75 Gremlin with a 304 that uses Prestolite dist. and had I think the pick up coil in the dist. go bad because changing the box and checking wires & plugs did not get the spark back. I say "think" as I needed to move the car and swapped in a Mallory pointless dist. Speaking of points the new points you get today are junk, more like the condensers are bad. Over time they go bad sitting on the shelf and being used in the dist. they also dont last forever. So just know if you go with points you can also have issues. Now for the DSII boxes and bad ones out of the box. This is also a issue with Fords, yes I have a 81 F100 pick up I did a 4 year cab off frame rebuild on. Mine was leaking the potting down the inner fender and before it stopped working I replaced it. Now what everyone should know there are low price parts and a high price parts and you get what you pay for. I went with a top of the line NAPA box and it has been running great for a year now and I put miles on this truck summer, high 90's, and winter, low 20's. Oh you have to ask for the top of the line parts because the counter people always go for the cheap ones because that is what everyone wants but not you! Just my .02 Dave ----
|
|
TSM = Technical Service Manual
75 Gremlin X v8 for sale 70 Javelin 360/auto drag car 70 Javelin 360/T5 Street car |
|
Mr_Roboto
AMC Apprentice Joined: Jun/12/2022 Location: Wisconsin Status: Offline Points: 221 |
Post Options
Thanks(0)
|
Nothing wrong with a big cap HEI. I really wish GM would have made a computer controlled variant for people like me who want to do EFI stuff. I think they would have been really great for EFI retrofits. The aftermarket for a large cap HEI is about as limitless as any ignition system out there I'd argue, and you can do neat stuff like get an adapter that lets you run an external coil which is handy and corrects what's probably one of the more contested parts of an HEI (running the coil in the cap.) I had looked at PNs before but never found one that was EFI ready. If anyone knows of one that'd be really fantastic, it would save me some fabrication.
Edited by Mr_Roboto - Jul/03/2022 at 11:23pm |
|
tomj
AMC Addicted Joined: Jan/27/2010 Location: earth Status: Offline Points: 7544 |
Post Options
Thanks(0)
|
The Duraspark distributor is fine, but the module is as FSjunkie says.
I have a 195.6 OHV distributor hacked up with a Duraspark reluctor setup and a 4 pin HEI module attached beneath. It works great. Tight fit. I didn't do the conversion.
|
|
1960 Rambler Super two-door wagon, OHV auto
1961 Roadster American, 195.6 OHV, T5 http://www.ramblerLore.com |
|
Post Reply | Page <12 |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |