Your donations help keep this valuable resource free and growing. Thank you.
|
Convertible top for 1963 American 440 |
Post Reply |
Author | |
MCP
AMC Fan Joined: Apr/26/2021 Location: 43081 Status: Offline Points: 21 |
Post Options
Thanks(0)
Posted: Apr/26/2021 at 5:58pm |
Hello,
I recently acquired a 1963 Rambler American 440. It is headed to our mechanic in a couple of days but meanwhile, we'd like to get the top up. The previous owner never had it out of the boot as he said the guy he got it from said it was a pain to get it put down. My question is, can we put it up manuallly? The togle switch on the dash doesn't do anything. We tried briefly to raise it but was afraid to force it at all. Any advise is appreciated! |
|
ramblinrev
Moderator Group Joined: Dec/28/2008 Location: Wisconsin Status: Offline Points: 11472 |
Post Options
Thanks(0)
|
Welcome, and congrats on your acquisition! I have a '62 convert! You have a power top. It's not meant to be raised or lowered manually. Probably what you need to do: 1. Carefully remove the rear quarter trim panels (those big panels beside the back seat.) 2. Disconnect the two hydraulic rams from the top mechanism. 3. Use a little clear lube, maybe WD40 on the mechanism hinge pivots that you can see. 4 Then I would suggest that two of you try to pull the top up. You don't want to bend any of the mechanism. Then you can do some troubleshooting: Are the hydraulic rams siezed? Does the motor/pump in the trunk run? It's all pretty basic stuff, but if it's been in the down position for a long time (and had issues before), you're probably going to need new pump, lines, and maybe the ram/cylinders. Good luck!
|
|
74 Hornet Hatchback X twins (since 1977)
62 American Convertible (still worth the $50 I spent in 1973!) AMCRC #513, AMO #384 70 AMX 360 4-speed (since 1981) |
|
MCP
AMC Fan Joined: Apr/26/2021 Location: 43081 Status: Offline Points: 21 |
Post Options
Thanks(0)
|
Thanks so much! I knew it had a motor which was why we were afraid to try and raise it manually. We will take a peek and see what we can find. Thanks again!
|
|
ramblinrev
Moderator Group Joined: Dec/28/2008 Location: Wisconsin Status: Offline Points: 11472 |
Post Options
Thanks(1)
|
Motor/pump combo will be in the trunk, on the rear axle hump. Hydraulic lines will run to it. The motor has a circuit breaker under the dash. Replacements are available. Google some of your questions like "how to fix my vintage convertible top motor" and that will help to. Hydro-Electric is one of the national known companies that supply those kinds of parts and advice.
|
|
74 Hornet Hatchback X twins (since 1977)
62 American Convertible (still worth the $50 I spent in 1973!) AMCRC #513, AMO #384 70 AMX 360 4-speed (since 1981) |
|
6768rogues
AMC Addicted Joined: Jul/03/2007 Location: United States Status: Offline Points: 6234 |
Post Options
Thanks(1)
|
My 66 American convertible has the pump behind the back of the rear seat. I put mine up manually but I had to go slowly because it was sucking fluid into the cylinders as it raised. It was not easy. I would pull out the seat back and Hotwire the pump to a battery. If the pump runs, ok. If it runs but the top doesn’t move, add fluid and help it by hand. If it doesn’t run, remove it and let the lines suck air as you raise it manually. It switches polarity to go up and down. I don’t have a wiring diagram in front of me.
|
|
Content intended for mature audiences. If you experience nausea or diarrhea, stop reading and seek medical attention.
Located usually near Rochester, NY and sometimes central FL. |
|
ramblinrev
Moderator Group Joined: Dec/28/2008 Location: Wisconsin Status: Offline Points: 11472 |
Post Options
Thanks(0)
|
It will go up much easier if you disconnect the rams. If the rods are rusty, they won't want to move anyway.
|
|
74 Hornet Hatchback X twins (since 1977)
62 American Convertible (still worth the $50 I spent in 1973!) AMCRC #513, AMO #384 70 AMX 360 4-speed (since 1981) |
|
MCP
AMC Fan Joined: Apr/26/2021 Location: 43081 Status: Offline Points: 21 |
Post Options
Thanks(0)
|
It is hard telling what we will find. I looked in the trunk and found the pump motor and a plastic tube connected to the canvas top via a fixture and a radiator clamp but it is just hanging down. There is no noise at all when we try the switch on the dash but so far have not seen anything disconnected under there - although the wires for lights/wipers were unplugged. I am fortunate to have gotten a large manual with the wiring diagrams etc included with the car so our neighbor took a look and at least got those hooked up so the turn signals etc are working. Hopefully they weren't unplugged because of an electrical problem a previous owner had and got tired of trying to figure out! As for the engine, the car runs but after it warms up will die unless given gas. (not fun when trying to shift gears...) Hopefully our mechanic will figure out that issue. If yours has a clutch, I'm curious - are they all adjusted so they have to be nearly all the way out to engage? This one is but I'm hoping it can be adjusted. I don't expect it to be quite like my modern car but hoping it can be a bit better. Thanks for your time!
|
|
ramblinrev
Moderator Group Joined: Dec/28/2008 Location: Wisconsin Status: Offline Points: 11472 |
Post Options
Thanks(1)
|
The plastic tube is a water drain tube, so the rainwater that flows in around the edges where the top meets the body, can be kept out of the trunk and interior! |
|
74 Hornet Hatchback X twins (since 1977)
62 American Convertible (still worth the $50 I spent in 1973!) AMCRC #513, AMO #384 70 AMX 360 4-speed (since 1981) |
|
farna
Supporter of TheAMCForum Moderator Lost Dealership Project Joined: Jul/08/2007 Location: South Carolina Status: Offline Points: 19611 |
Post Options
Thanks(1)
|
I'd pull the hydraulic pump and rams and check with a battery or 12V power supply on a bench. If a hose has a leak (they are OLD!!) you don't want to dump fluid all in the car where it will be hard to clean up. It's a bit of work to remove it all, but you probably want to have new hoses made unless you can verify that the ones you have are less than 10 years old. Any hydraulic shop can make hoses and rebuild the cylinders, possibly the pump. Any 12V pump will technically work, so they may have a better replacement option -- though most shops are going to be for HD equipment with engine driven pumps. With the cylinders (rams) disconnected you should be able to raise and lower the top manually with two people, just be careful and go kind of slow.
|
|
Frank Swygert
|
|
MCP
AMC Fan Joined: Apr/26/2021 Location: 43081 Status: Offline Points: 21 |
Post Options
Thanks(0)
|
Actually we were very fortunate that the pump was just a bit "seized up" and when our mechanic "talked nicely to it!" it unseized and with a flip of the switch the top went up and is in quite good shape (one small rip on outer section - not clear through). We were all amazed! Thanks for your advice in any event!
|
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |