Your donations help keep this valuable resource free and growing. Thank you.
|
Can I reuse my Moly piston rings? |
Post Reply |
Author | |
rang-a-stang
AMC Nut Joined: Sep/25/2018 Location: Camarillo, CA Status: Offline Points: 272 |
Post Options
Thanks(0)
Posted: Nov/20/2020 at 8:00pm |
My 401 block is at the machinist from low oil pressure. My moly rings have about 8,000 miles on them and my compression was good before I opened up the motor. Wiseco forged pistons/rings, 9.5:1, daily driver.
Machine shop is cleaning the block and then is going to hone it. Is there any reason I could not just stick the same piston down the same hole with the same rings (after some cleaning)?
|
|
79 Cherokee, 401
|
|
WesternRed
AMC Addicted Joined: Aug/03/2010 Location: Australia Status: Offline Points: 5798 |
Post Options
Thanks(0)
|
If you are going to hone then maybe new rings on the old pistons would be the go, rings are not very expensive.
|
|
I've finally given up drinking for good...........now I only drink for evil.
|
|
JGRANTAMX
AMC Addicted Joined: Jun/02/2017 Location: Maine Status: Offline Points: 1697 |
Post Options
Thanks(0)
|
Rings wear into the cylinder similar to bearings on the crankshaft, low mileage rings could be put back if they were oriented exactly the same as before in each cylinder without honing, rings are not intended to be run in more than once so time for a new set. I have a new set of the Wiseco flat top pistons they use thin rings that cost more.
J
|
|
mixed up
AMC Addicted Joined: Jun/16/2015 Location: Monroe mich Status: Offline Points: 2177 |
Post Options
Thanks(3)
|
for the cost of the rings and a piece of mind why reuse them
|
|
69 amx 290 auto
65 220 290 4spd 80 ford fairmont |
|
PROSTOCKTOM
Supporter of TheAMCForum Joined: Jun/20/2010 Location: Indiana Status: Offline Points: 2450 |
Post Options
Thanks(0)
|
I would never put a set back in a block after they have been removed with 8,000 miles on them. Rings work because of tension and they are heat cycled to fit that bore. Once you pull them out of a bore they would never obtain the same level of seal they had when first installed. Run a hone through it, toss out the old rings, and go buy a new set. You'll be glad you did.
Tom |
|
Molnar Technologies Full Service Dealer - Crankshafts & Connecting Rods
1969 AMC Rambler Rouge Race Car 1974 AMC Hornet Hatchback, Wally Booth Outlaw Nostalgic Pro Stock Race Car Project |
|
Boris Badanov
AMC Addicted Joined: Dec/14/2013 Location: NH USA Status: Offline Points: 4209 |
Post Options
Thanks(0)
|
Best to replace them.
Why risk pulling it down again...
|
|
Gremlin Dreams
|
|
Hurst390
AMC Addicted Joined: Apr/20/2008 Location: secret Status: Offline Points: 5818 |
Post Options
Thanks(0)
|
|
|
SC/Hurst Rambler
11.62 120 100% Street Legal |
|
Hurst390
AMC Addicted Joined: Apr/20/2008 Location: secret Status: Offline Points: 5818 |
Post Options
Thanks(0)
|
I have a 360 in a street car. It was a reman engine that had sat outside for a bit. 2 cylinders had some pitting. I cleaned it up the best I could with a rigid hone and re assembled it with new gaskets. Re-using all the bearings and rings. I drive it to work daily and has yet to use a drop of oil in the last 2 years.I don't recommend everyone to be a caveman builder but it works for me.
|
|
SC/Hurst Rambler
11.62 120 100% Street Legal |
|
rang-a-stang
AMC Nut Joined: Sep/25/2018 Location: Camarillo, CA Status: Offline Points: 272 |
Post Options
Thanks(0)
|
New moly rings are $150 (including shipping and tax) and won't get here for 2 weeks. If they were much cheaper and I could get them quickly I would do it for sure but I just don't think I have the $$ and don't want to wait to save up. When I had it bored from the first rebuild (8k miles ago), they used torque plates so I feel a little better about throwing them in.
It sounds like it is not ideal to reuse them but it also sounds like it is not a death sentence, either. Maybe if the machine shop takes another couple weeks, I'll order some rings.
|
|
79 Cherokee, 401
|
|
JGRANTAMX
AMC Addicted Joined: Jun/02/2017 Location: Maine Status: Offline Points: 1697 |
Post Options
Thanks(0)
|
Decades ago when I was learning engines I freshened up a 307 SBC after about 2K Mi. it was still burning a considerable amount of oil embarrassing blue smoke, frustrated I pulled it out took it apart while doing that I sketched where the ring gaps were in the cylinders, I thought somehow I got a bum set of rings. It was determined the hone stones I used was too fine for the the ring set I used the machine shop I consulted said it a was called a "wet set of rings" and to put them back and they would run in I did it took awhile but it did stop burning oil, I learned that one the hard way. It can be done however where your cylinders were honed I wouldn't do it, what is the rush? When you fire it up do you want in your mind "I hope these rings are going to be good?" Better safe than sorry!
J
Edited by JGRANTAMX - Nov/22/2020 at 7:41am |
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |