Your donations help keep this valuable resource free and growing. Thank you.
|
Need some AC advice/help EXP VALVE FIXED!!!!!! |
Post Reply | Page <1 234 |
Author | ||
401MATCOUPE
AMC Addicted Joined: May/20/2010 Location: Salisbury, MD Status: Offline Points: 5367 |
Post Options
Thanks(0)
|
|
Did you change the expansion valve to something other then the original fittings? I am not understanding the issue???
|
||
Ross K. Peterson
68X,GoPac,343,AT,52A(1stCar) 68X,GoPac,390,4sp,52A 69X,GoPac,390,4sp,64A 70X,GoPac,390,4sp,87A,8 70X,GoPac,390,4sp,BBO,8 70 Jav SST,390,AT,BSO 74MatX,401,AT,Prototype 74MatX,401,AT |
||
Mopar_guy
Supporter of TheAMCForum Joined: Jun/07/2009 Location: Ohio Status: Offline Points: 4837 |
Post Options
Thanks(0)
|
|
Back on page 2 "No OEM parts, everything is aftermarket. "
|
||
"Hemilina" My 1973, 5.7 Hemi swapped Javelin |
||
401MATCOUPE
AMC Addicted Joined: May/20/2010 Location: Salisbury, MD Status: Offline Points: 5367 |
Post Options
Thanks(0)
|
|
Okay, is aftermarket changes, I can not help any further.....thank you.
|
||
Ross K. Peterson
68X,GoPac,343,AT,52A(1stCar) 68X,GoPac,390,4sp,52A 69X,GoPac,390,4sp,64A 70X,GoPac,390,4sp,87A,8 70X,GoPac,390,4sp,BBO,8 70 Jav SST,390,AT,BSO 74MatX,401,AT,Prototype 74MatX,401,AT |
||
Texas275
Supporter of TheAMCForum Joined: Dec/18/2013 Location: Forney, Tx Status: Offline Points: 469 |
Post Options
Thanks(0)
|
|
Finally got back to the shop with an expansion valve that fit. Evacuated the system, recharged, and it works great. Thanks so much for helping me fix it!!!! Y’all are the best!!
Tom
|
||
Mopar_guy
Supporter of TheAMCForum Joined: Jun/07/2009 Location: Ohio Status: Offline Points: 4837 |
Post Options
Thanks(0)
|
|
I figured that was it. Glad you got it fixed and thanks for reporting back.
|
||
"Hemilina" My 1973, 5.7 Hemi swapped Javelin |
||
Heavy 488
AMC Addicted Joined: Apr/27/2019 Location: In the Status: Offline Points: 3557 |
Post Options
Thanks(0)
|
|
|
||
FSJunkie
AMC Addicted Joined: Jan/09/2011 Location: Flagstaff, AZ Status: Offline Points: 4742 |
Post Options
Thanks(0)
|
|
It is important that the thermal bulb of the expansion valve is attached firmly and directly to the outlet line of the evaporator then wrapped in insulation. Without this, the expansion valve will think the evaporator outlet is warm and the valve will open wider to admit more refrigerant. High side pressure will drop, low side pressure will rise, and the compressor will slug with liquid refrigerant. You will eventually blow the compressor.
R12 and R134a expansion valves have a slightly different superheat setting but only slightly and not enough to cause this. There is also the question of system charge amount. Even with a wide open expansion valve, there should not be any bubbles in the sights glass while the compressor is running. Charge amount does not effect the cooling effectiveness of expansion valve type A/C systems. All they care about is that there is enough refrigerant to keep the pickup tube in the receiver/dryer submerged in liquid refrigerant. Adding refrigerant just raises the liquid level. Bubbles in the sight glass means the pickup tube is not submerged, so you add refrigerant until the bubbles disappear then add a little more to give it some reserve. |
||
1955 Packard
1966 Marlin 1972 Wagoneer 1973 Ambassador 1977 Hornet 1982 Concord D/L 1984 Eagle Limited |
||
rushtonmd
AMC Apprentice Joined: Apr/17/2020 Location: San Diego, CA Status: Offline Points: 57 |
Post Options
Thanks(0)
|
|
Good call on the expansion valve. I built a custom AC system for a VW and the expansion valve that I got from the company was sized too small for the system. It was a 1ton valve - I did the same thing where I trolled the Oreilly site until I found a 1.5 to. valve with the correct fittings and it all worked great. A lot of AC system companies sell the same valve for all systems and it’s good to check the size against system size - but also they’re super cheap which is nice :) I think mine was like $15.
One other thing is there are metric fittings as well as AN fittings so sometimes you’ll have to mix and match with adapters or make sone adapter hoses.
|
||
Post Reply | Page <1 234 |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |