Your donations help keep this valuable resource free and growing. Thank you.
|
Need some AC advice/help EXP VALVE FIXED!!!!!! |
Post Reply | Page <1234> |
Author | |
Heavy 488
AMC Addicted Joined: Apr/27/2019 Location: In the Status: Offline Points: 3557 |
Post Options
Thanks(0)
|
You already saw the compressor able to hit 150 with the suction closed. what target number were you shooting for that needs another compressor?
|
|
Texas275
Supporter of TheAMCForum Joined: Dec/18/2013 Location: Forney, Tx Status: Offline Points: 469 |
Post Options
Thanks(0)
|
I agree with you. That's why I'm replacing the valve.
|
|
george w
Supporter of TheAMCForum Joined: Jan/27/2013 Location: New Jersey Status: Offline Points: 2899 |
Post Options
Thanks(0)
|
Sure sounds like the expansion valve is stuck open. The system depends on that restriction to develop the pressure differential.
|
|
Long time AMC fan. Ambassador 343, AMX 390, Hornet 360, Spirit 304 and Javelin 390. All but javelin bought new.
|
|
Texas275
Supporter of TheAMCForum Joined: Dec/18/2013 Location: Forney, Tx Status: Offline Points: 469 |
Post Options
Thanks(0)
|
So I came up with a question as I was pulling the expansion valve off.
Does the expansion valve have to be oriented in any particular position. Mine is in upside down, silver flat disc down. That’s how I had to place the evaporator behind the dash. Would that keep it from working properly? If it has to be turned over, can I add a U shaped line to move it and turn it right side up, To keep from having to move the evaporator?
|
|
Heavy 488
AMC Addicted Joined: Apr/27/2019 Location: In the Status: Offline Points: 3557 |
Post Options
Thanks(0)
|
Only flow direction should matter, not rotation.
|
|
Texas275
Supporter of TheAMCForum Joined: Dec/18/2013 Location: Forney, Tx Status: Offline Points: 469 |
Post Options
Thanks(0)
|
Got it, Thanks
|
|
Texas275
Supporter of TheAMCForum Joined: Dec/18/2013 Location: Forney, Tx Status: Offline Points: 469 |
Post Options
Thanks(0)
|
I took my expansion valve to the local Orileys and they brought out 10 different ones to see if they would fit. None of them fit. They all said #6 and #8 male ends but the #8 was too big for my fitting to screw onto.
I have ordered one from Nostalgic Air. I’m hoping it fits and I don’t have some weird, one off, expansion valve.
|
|
george w
Supporter of TheAMCForum Joined: Jan/27/2013 Location: New Jersey Status: Offline Points: 2899 |
Post Options
Thanks(0)
|
Using R-12 or R-134 and does it matter ? Shouldn't the usual AMC vendors have the proper valve ?
|
|
Long time AMC fan. Ambassador 343, AMX 390, Hornet 360, Spirit 304 and Javelin 390. All but javelin bought new.
|
|
304-dude
AMC Addicted Joined: Sep/29/2008 Location: Central Illinoi Status: Offline Points: 9082 |
Post Options
Thanks(0)
|
Well it could be defective, as it is a low cost item, that is a wee bugger to get to if all finished up. As for difference yes there is. But most are happy with original R12 valve. If your doing a whole new kit or upgrade, I suggest obtaining R134 valve if possible to swap out. It does make it cooler, as the system does not cycle as much. It should cycle once every 2 minutes, but it depends on capacity and tempratures. Between once every minute or two is good. The less cycling the more efficient the system. |
|
71 Javelin SST body
390 69 crank, 70 block & heads NASCAR SB2 rods & pistons 78 Jeep TH400 w/ 2.76 Low 50/50 Ford-AMC Suspension 79 F150 rear & 8.8 axles Ford Racing 3.25 gears & 9" /w Detroit locker |
|
Texas275
Supporter of TheAMCForum Joined: Dec/18/2013 Location: Forney, Tx Status: Offline Points: 469 |
Post Options
Thanks(0)
|
The evap is set up as 134. It is a cheap model and I may be paying for that now. I put the numbers that are on the valve into google and it only came back with a few results, all of them overseas, and only a couple in English
|
|
Post Reply | Page <1234> |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |