Your donations help keep this valuable resource free and growing. Thank you.
|
Drip Rail Trim Repair |
Post Reply |
Author | |
3250man
Supporter of TheAMCForum Joined: Jun/14/2019 Location: WA Status: Offline Points: 285 |
Post Options
Thanks(0)
Posted: Nov/29/2020 at 6:17pm |
Worked on the window drip rail trim today. Lots of
crud in the locking channels and I had to go real slow to remove the trim. As
you can see, the removal tool (bottle opener), left some marks. I’m open to any advice/tricks-of-the-trade to get
them smoothed out. This is my first time to attempt this. Watched several YouTube
videos and decide to attempt to fix them. Thanks. |
|
1974 Mellow Yellow N-code AMX (restoring)- "Steve"
2016 Chevy Colorado (RIPP supercharged V6) 1973 Corvette 1974 Trans AM Red P-code AMX |
|
turbo
AMC Addicted Joined: Oct/26/2008 Location: chicago area Status: Offline Points: 2566 |
Post Options
Thanks(0)
|
First, you can not use a bottle opener to remove trim. Ruins it. Use a 1 1/2 inch wide hard wood block and tap off lower edge little at a time. Yours may be toast.....I could do it but it takes a certain amount of attention to detail. it would take a professional restorer a good bit of effort to repair yours. No worries, easy enough to get another set and re install. You have made a very common mistake.
|
|
they call me Capt RETIRED!
|
|
tufcj
Supporter of TheAMCForum Supporter of TheAMCForum Joined: Jul/10/2007 Location: Watkins, CO Status: Offline Points: 4068 |
Post Options
Thanks(0)
|
My AMX came with the drip rail trim looking like someone attacked it with a hammer. I watched all kinds of videos, and bought hammers and a buffing wheel kit. I tried and found I didn't have the knack for it. Sent it to "The Finishing Touch" in Chicago. Came back looking new. Ran about $35 a linear foot. It was money well spent and just a small fraction of the total cost of restoring the AMX. Bob tufcj
|
|
69 AMX
74 Javelin AMX 67 Rogue If you need a tool and don't buy it... you'll eventually pay for it... and not have it. Henry Ford |
|
turbo
AMC Addicted Joined: Oct/26/2008 Location: chicago area Status: Offline Points: 2566 |
Post Options
Thanks(0)
|
Yea, they're good.......Took about a year for a bumper chroming for me though. You do NOT want to cheap out on the look of your stainless, however. Bad stainless will make an otherwise GREAT car look like an overlooked turd. That and the glass are often overlooked.
|
|
they call me Capt RETIRED!
|
|
Steve_P
AMC Addicted Charter Member Joined: Jun/28/2007 Status: Online Points: 3761 |
Post Options
Thanks(0)
|
There are probably more than 20 threads on here saying to use a block of hardwood and knock it off from the inside out. I've posted it many times. Lesson learned. Now get out the credit card.
|
|
1BadJav
AMC Nut Joined: Mar/07/2008 Location: Las Vegas, NV Status: Offline Points: 342 |
Post Options
Thanks(0)
|
I might have a decent set, from a 72/73 Javelin. I can check tomorrow.
|
|
72 AMC Javelin SST - 401/727
|
|
Steve_P
AMC Addicted Charter Member Joined: Jun/28/2007 Status: Online Points: 3761 |
Post Options
Thanks(0)
|
Your best bet will be to get a set that's been properly removed. If it's from a 71-4 Javelin, it'd be the cheapest route versus to restore what you have. And do not hammer them on with a rubber mallet! Wrap a block of wood with a rag and press them on. Start at the sharp bends and work away.
|
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |