TheAMCForum.com Homepage
Forum Home Forum Home > The Lounge Area > Member Projects
  New Posts New Posts RSS Feed - XRV8 Gremlin
  FAQ FAQ  Forum Search   Events   Register Register  Login Login

Click for TheAMCForum Rules / Click for PDF version of Forum Rules
Your donations help keep this valuable resource free and growing. Thank you.

XRV8 Gremlin

 Post Reply Post Reply Page  <1 484950
Author
Message
farna View Drop Down
Supporter of TheAMCForum
Supporter of TheAMCForum
Avatar
Moderator Lost Dealership Project

Joined: Jul/08/2007
Location: South Carolina
Status: Offline
Points: 16737
Post Options Post Options   Thanks (0) Thanks(0)   Quote farna Quote  Post ReplyReply Direct Link To This Post Posted: Feb/17/2020 at 5:52am
g-man, the 250/287/327 are all virtually the same except for the bore (1/4" difference in each). The 250 had solid lifters instead of hydraulic, but I think all the passages are there so you could run hydraulics by installing them and either adjusting the 250 rockers or using 287/327 rockers. Not sure about that though, might be a difference in oil passages or something that isn't obvious (drilled differently?). Other than that there is just a difference in the early and late blocks. 63-66 blocks have a pad cast into them for the side motor mounts, but still have the (undrilled) pad for the forward mounts (56-62 used two forward mounts on engine and two on the bell housing in the rear instead of one each side and a transmission mount like 63+).
Frank Swygert
Back to Top
amcenthusiast View Drop Down
AMC Addicted
AMC Addicted
Avatar

Joined: Jul/02/2012
Location: central Texas
Status: Offline
Points: 1432
Post Options Post Options   Thanks (0) Thanks(0)   Quote amcenthusiast Quote  Post ReplyReply Direct Link To This Post Posted: Feb/18/2020 at 1:20pm
Farna I believe you are a very likeable, kind and generous person.



Edited by amcenthusiast - Feb/18/2020 at 4:37pm
Link to XRV8 Race Parts website: www.amcramblermarlin.1colony.com
Back to Top
304-dude View Drop Down
AMC Addicted
AMC Addicted
Avatar

Joined: Sep/29/2008
Location: Central Illinoi
Status: Offline
Points: 7661
Post Options Post Options   Thanks (0) Thanks(0)   Quote 304-dude Quote  Post ReplyReply Direct Link To This Post Posted: Feb/18/2020 at 1:40pm
Originally posted by amcenthusiast amcenthusiast wrote:

No they are not all virtually the same.

The three main types of fallacy that smear the reputation of nearly all AMC products are:

1) Disinformation (deliberate lies)
2) Misinformation (lies by mistake)
3) No information (lying by omission)

The most noteworthy difference among all Rambler V8 engine blocks is that only the 4bbl 327 blocks feature solid main webs; all others have 'windowed mains' for weight reduction.


Wasn't the block you used specific to 1965 year, which had some other changes? I would have to go back and read through your details, but figure you would state the details quicker, than I.




71 Javelin SST body
390 69 crank, 70 block & heads
NASCAR SB2 rods & pistons
78 Jeep TH400 w/ 2.76 Low
50/50 Ford-AMC Suspension
79 F150 rear & 8.8 axles
Ford Racing 3.25 gears & 9" /w Detroit locker
Back to Top
amcenthusiast View Drop Down
AMC Addicted
AMC Addicted
Avatar

Joined: Jul/02/2012
Location: central Texas
Status: Offline
Points: 1432
Post Options Post Options   Thanks (0) Thanks(0)   Quote amcenthusiast Quote  Post ReplyReply Direct Link To This Post Posted: Feb/18/2020 at 2:02pm
Hey 304dude!

I used a '64 2bbl 327 long block for this engine build.

I like this because it shows one example of what we can do with a more common windowed main block.

-Still inching closer to the day when I will be able to run this car on an official 1/4 mile dragstrip to get a rough estimate of it's power making potential.

Perhaps sometime in the next six months, if all goes well/no unexpected problems.
Link to XRV8 Race Parts website: www.amcramblermarlin.1colony.com
Back to Top
304-dude View Drop Down
AMC Addicted
AMC Addicted
Avatar

Joined: Sep/29/2008
Location: Central Illinoi
Status: Offline
Points: 7661
Post Options Post Options   Thanks (0) Thanks(0)   Quote 304-dude Quote  Post ReplyReply Direct Link To This Post Posted: Feb/18/2020 at 2:10pm
Originally posted by amcenthusiast amcenthusiast wrote:

Hey 304dude!

I used a '64 2bbl 327 long block for this engine build.

I like this because it shows one example of what we can do with a more common windowed main block.

-Still inching closer to the day when I will be able to run this car on an official 1/4 mile dragstrip to get a rough estimate of it's power making potential.

Perhaps sometime in the next six months, if all goes well/no unexpected problems.



ah, I may have confused your block, as had explained, something about 65, and 66 Calif. engines, could have been intake or smog differences. Just seemed that you covered a lot of details, that non Rambler engine people, like me can get overwhelmed with. Thanks, for clarification... and yes it will be amazing to see it run a 1/4 mile. I am sure you have gotten your carb setup pretty much dialed in. Sure hate to see a carb give you a bad run.
71 Javelin SST body
390 69 crank, 70 block & heads
NASCAR SB2 rods & pistons
78 Jeep TH400 w/ 2.76 Low
50/50 Ford-AMC Suspension
79 F150 rear & 8.8 axles
Ford Racing 3.25 gears & 9" /w Detroit locker
Back to Top
amcenthusiast View Drop Down
AMC Addicted
AMC Addicted
Avatar

Joined: Jul/02/2012
Location: central Texas
Status: Offline
Points: 1432
Post Options Post Options   Thanks (0) Thanks(0)   Quote amcenthusiast Quote  Post ReplyReply Direct Link To This Post Posted: Feb/18/2020 at 4:32pm
OK yes that's another significant factor one should consider when searching for used Rambler V8 engine parts:

-All '66 RV8s (and '66/7 Jeep 'Vigilante V8') cylinder heads were made having air injection bosses cast into the exhaust ports of the heads.

-The air injection boss does protrude into a critical high pressure area of the port which obviously hinders exhaust flow.

Yes, while they can be ported to remove the air injection bosses, it's not an easy task.

Because of the difficulty, I'd recommend non-air injection heads for any higher performance type engine build.
Link to XRV8 Race Parts website: www.amcramblermarlin.1colony.com
Back to Top
rsrguy3 View Drop Down
AMC Apprentice
AMC Apprentice


Joined: Jun/24/2012
Location: Utah
Status: Online
Points: 222
Post Options Post Options   Thanks (0) Thanks(0)   Quote rsrguy3 Quote  Post ReplyReply Direct Link To This Post Posted: Feb/18/2020 at 10:28pm
So what’s the inside painted with? My good friend painted my lifter valley and it all let go and ruined the build... 
javguy
Back to Top
rsrguy3 View Drop Down
AMC Apprentice
AMC Apprentice


Joined: Jun/24/2012
Location: Utah
Status: Online
Points: 222
Post Options Post Options   Thanks (0) Thanks(0)   Quote rsrguy3 Quote  Post ReplyReply Direct Link To This Post Posted: Feb/18/2020 at 10:29pm
So what’s the inside painted with? My good friend painted my lifter valley and it all let go and ruined the build... 
javguy
Back to Top
 Post Reply Post Reply Page  <1 484950
  Share Topic   

Forum Jump Forum Permissions View Drop Down



This page was generated in 0.078 seconds.
All content of this site Copyright © 2018 TheAMCForum unless otherwise noted, all rights reserved.
PROBLEMS LOGGING IN or REGISTERING:
If you have problems logging in or registering, then please contact a Moderator or