![]() |
|
Your donations help keep this valuable resource free and growing. Thank you.
|
sick 727 |
Post Reply
|
Page 123 9> |
| Author | |
1970390amx
AMC Addicted
Joined: Jul/12/2008 Location: colorado Status: Offline Points: 1232 |
Post Options
Thanks(0)
Quote Reply
Topic: sick 727Posted: May/17/2012 at 11:32pm |
|
The soeedo housing has the hole offset from center. The housing rotates depending on the gear used. Count the teeth on the gear you will use, and find the marking on the housing that matches the tooth count. Align the marking on the speedo housing that matches the speedo gear count with the mark on the tailhousing.
|
|
|
1970 390 4speed Bittersweet shadow mask AMX
1970 Amx missing most everything, or in a box |
|
![]() |
|
1970390amx
AMC Addicted
Joined: Jul/12/2008 Location: colorado Status: Offline Points: 1232 |
Post Options
Thanks(0)
Quote Reply
Posted: May/17/2012 at 11:25pm |
|
Somehow I never took any pictures of this transmission done, so I will end with a picture of some special tools. The one on the right is made to remove the manual lever seal in the car with out damage to anything. The one on the left is a driver to install the seal.
|
|
|
1970 390 4speed Bittersweet shadow mask AMX
1970 Amx missing most everything, or in a box |
|
![]() |
|
1970390amx
AMC Addicted
Joined: Jul/12/2008 Location: colorado Status: Offline Points: 1232 |
Post Options
Thanks(0)
Quote Reply
Posted: May/17/2012 at 11:19pm |
|
The springs at right are not used in a lot of applications. The new manual valve helps prevent converter drain back and has provisions for cooler flow with the transmission in park.
|
|
|
1970 390 4speed Bittersweet shadow mask AMX
1970 Amx missing most everything, or in a box |
|
![]() |
|
1970390amx
AMC Addicted
Joined: Jul/12/2008 Location: colorado Status: Offline Points: 1232 |
Post Options
Thanks(0)
Quote Reply
Posted: May/17/2012 at 11:13pm |
|
Several holes in the separater plate are enlarged when a shift kit is used.
|
|
|
1970 390 4speed Bittersweet shadow mask AMX
1970 Amx missing most everything, or in a box |
|
![]() |
|
1970390amx
AMC Addicted
Joined: Jul/12/2008 Location: colorado Status: Offline Points: 1232 |
Post Options
Thanks(0)
Quote Reply
Posted: May/17/2012 at 11:09pm |
|
I very rarely take the valve body totally apart, I clean it in solvent and check the movement of valves with a pick. The manual valve and pressure regulator springs are changed in the shift kit I use.
|
|
|
1970 390 4speed Bittersweet shadow mask AMX
1970 Amx missing most everything, or in a box |
|
![]() |
|
1970390amx
AMC Addicted
Joined: Jul/12/2008 Location: colorado Status: Offline Points: 1232 |
Post Options
Thanks(0)
Quote Reply
Posted: May/17/2012 at 11:02pm |
|
The intermediate band struts are shown installed, with the pump insalled you can adjust the band now. The apply lever is available in different ratios. If you remove it from the transmission the side of it has a number stamped into it. The higher the number the firmer hold it will provide. Mopar performance web sites are the place to look for them.
|
|
|
1970 390 4speed Bittersweet shadow mask AMX
1970 Amx missing most everything, or in a box |
|
![]() |
|
1970390amx
AMC Addicted
Joined: Jul/12/2008 Location: colorado Status: Offline Points: 1232 |
Post Options
Thanks(0)
Quote Reply
Posted: May/17/2012 at 10:55pm |
|
The pump bolts have a sealing washer under the head. The can cause a leak if left out.
|
|
|
1970 390 4speed Bittersweet shadow mask AMX
1970 Amx missing most everything, or in a box |
|
![]() |
|
1970390amx
AMC Addicted
Joined: Jul/12/2008 Location: colorado Status: Offline Points: 1232 |
Post Options
Thanks(0)
Quote Reply
Posted: May/17/2012 at 10:53pm |
|
I use special alignment studs to keep the pump gasket aligned as the pump is installed. Sometimes the pump needs a nudge with a hammer to drive it home.
|
|
|
1970 390 4speed Bittersweet shadow mask AMX
1970 Amx missing most everything, or in a box |
|
![]() |
|
1970390amx
AMC Addicted
Joined: Jul/12/2008 Location: colorado Status: Offline Points: 1232 |
Post Options
Thanks(0)
Quote Reply
Posted: May/17/2012 at 10:48pm |
|
The front and rear drum installation is fairly straight forward. The clutches need to align with the input of the transmission. When fully installed there will be a solid thunk, and the front drum will align with the sun shell like shown in the picture.
|
|
|
1970 390 4speed Bittersweet shadow mask AMX
1970 Amx missing most everything, or in a box |
|
![]() |
|
1970390amx
AMC Addicted
Joined: Jul/12/2008 Location: colorado Status: Offline Points: 1232 |
Post Options
Thanks(0)
Quote Reply
Posted: May/17/2012 at 10:43pm |
|
The front and rear drums can be set into the transmission as an assembly. Then the intermediate band can be set into place around the front drum.
|
|
|
1970 390 4speed Bittersweet shadow mask AMX
1970 Amx missing most everything, or in a box |
|
![]() |
|
Post Reply
|
Page 123 9> |
|
Tweet
|
| Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |