Your donations help keep this valuable resource free and growing. Thank you.
|
Stalling engine |
Post Reply | Page 12> |
Author | |
apollotaki
AMC Apprentice Joined: May/25/2017 Location: Massachusetts Status: Offline Points: 91 |
Post Options
Thanks(0)
Posted: Nov/13/2017 at 7:50am |
HELP!!! I have a 1959 Rambler Super with a six cylinder engine and automatic transmission. I runs and idles fine but when I put it into drive or reverse it stalls out. The revs seem to be high enough when I try to engage the trans. What is going on? Thanks for any suggestions.
|
|
carnuck
AMC Addicted Joined: Mar/31/2010 Location: Seattle Status: Offline Points: 3942 |
Post Options
Thanks(0)
|
Look down the throat of the carb and see if gas is spilling over from excessively high float (video with sound can work if you can’t tell) aside from that the valves may be too tight or a vacuum leak. Have you tried pulling the driveshaft and sticking it in gear? If it still stalls, then a transmission problem is suggested likely.
|
|
Got an Eagle?
http://forums.amceaglesden.com |
|
apollotaki
AMC Apprentice Joined: May/25/2017 Location: Massachusetts Status: Offline Points: 91 |
Post Options
Thanks(0)
|
Thanks, I'll check it out.
|
|
jimmy joe
AMC Fan Joined: Dec/13/2018 Location: Michigan Status: Offline Points: 7 |
Post Options
Thanks(0)
|
did you find out what was causing your car to stall?
|
|
apollotaki
AMC Apprentice Joined: May/25/2017 Location: Massachusetts Status: Offline Points: 91 |
Post Options
Thanks(0)
|
I advanced the timing a bit and messed with the carb. and it seems OK for now. Thanks for asking.
|
|
jimmy joe
AMC Fan Joined: Dec/13/2018 Location: Michigan Status: Offline Points: 7 |
Post Options
Thanks(0)
|
I have a 65 rambler american as soon as I shift into forward or reverse the car dies its very frustrating
|
|
andyleonard
AMC Apprentice Joined: Dec/10/2016 Location: 90290 Status: Offline Points: 138 |
Post Options
Thanks(0)
|
You may want to adjust the modulator on the trans. Mine did that and a turn or 2 corrected it.
|
|
pacerman
Supporter of TheAMCForum Joined: Jul/03/2007 Location: United States Status: Offline Points: 9048 |
Post Options
Thanks(0)
|
I recommend you check your timing and the idle mixture both hot and cold. In other words, make sure the choke plate is adjusted properly at the cold setting and then with the engine warms up fully, make sure the choke plate is vertical or nearly so. Check your base timing with the engine at normal hot idle about 600 rpm or so and the distributor vacuum hose disconnected at the distributor and plugged. When that is done, make sure the idle mixture is properly set. Also, check for vacuum leaks. Low power and poor response to throttle advance are classic signs of a lean mixture or improper timing. The service manual has all the proper instructions for setting the mixture and timing. Joe
|
|
Happiness is making something out of nothing.
|
|
tomj
AMC Addicted Joined: Jan/27/2010 Location: earth Status: Offline Points: 7522 |
Post Options
Thanks(0)
|
that's not a lot of information; but unless something unmentioned that is truly odd is going on, generally that sounds like a top to bottom tuneup is needed. carburetor and ignition work together (or fight each other, lol) especially at idle/low speeds. |
|
1960 Rambler Super two-door wagon, OHV auto
1961 Roadster American, 195.6 OHV, T5 http://www.ramblerLore.com |
|
jimmy joe
AMC Fan Joined: Dec/13/2018 Location: Michigan Status: Offline Points: 7 |
Post Options
Thanks(0)
|
thanks for the information I'll check those things out the car's a 232 engine 2 bbl carburetor and an automatic transmission
|
|
Post Reply | Page 12> |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |