Your donations help keep this valuable resource free and growing. Thank you.
|
Sanity Check My Tuning |
Post Reply | Page <12 |
Author | |
Red20
AMC Addicted Joined: Jan/29/2013 Location: Oceanside CA Status: Offline Points: 1556 |
Post Options
Thanks(0)
|
I made a vacuum advance stop plate for my MSD billet distributor. It was advancing 18* (advertised 16*) and I'd really prefer about 10*.
BUT...I mismeasured when I trimmed the stop tab (see yellow arrow) and it now advances 17*. I just shook my head and went inside. I'll make another one later today. I'm pleased with the design though. |
|
1969 Javelin SST "Screamin' Banana" - Totaled Feb 2018
1973 Hornet Sportabout X "yellajack" - 360/727/TracLoc DAILY DRIVER |
|
Bandana
AMC Nut Joined: Jul/26/2016 Location: NC Status: Offline Points: 473 |
Post Options
Thanks(0)
|
Interesting modification. Never really looked how the vacuum advance works on these. I also seem to be getting too much advance from my billet and have disconnected it for now to keep from pinging. When you get yours set to limit the advance to 10 degrees can you post more detail on it? I assume you need a longer tab on the stop?
|
|
ccowx
AMC Addicted Joined: Nov/03/2010 Location: Yukon Status: Offline Points: 3510 |
Post Options
Thanks(0)
|
You could try a set up like this. Easier to adjust but the same effect.
My edit is that there is no way to upload an image!!!!!!!!!!! If you want a picture of something similar to what you have that is adjustable and basically free, please PM me. Thanks! Chris PS: Yes, I have done the image upload and post many times, it is not working now. Edited by ccowx - Jul/21/2017 at 10:37am |
|
Red20
AMC Addicted Joined: Jan/29/2013 Location: Oceanside CA Status: Offline Points: 1556 |
Post Options
Thanks(0)
|
I emailed you, Chris.
|
|
1969 Javelin SST "Screamin' Banana" - Totaled Feb 2018
1973 Hornet Sportabout X "yellajack" - 360/727/TracLoc DAILY DRIVER |
|
Red20
AMC Addicted Joined: Jan/29/2013 Location: Oceanside CA Status: Offline Points: 1556 |
Post Options
Thanks(0)
|
I'll take a few more pictures when I pull it off in a bit. I'm anxious to see what ccowx's solution entails. Adjustability is certainly good. As for the piece I made, it's just a piece of aluminum I cut on a scroll saw with a fine tooth wood blade. I mocked it up first in cardboard from the end flap of a 12 pack box. Probably took me 15 minutes. The rear screw for the canister is pretty short, so I counter sunk it a hair with a forstner bit. I like aluminum because if you're not going for fine finish work, a lot of wood tools will cut it just fine. |
|
1969 Javelin SST "Screamin' Banana" - Totaled Feb 2018
1973 Hornet Sportabout X "yellajack" - 360/727/TracLoc DAILY DRIVER |
|
Red20
AMC Addicted Joined: Jan/29/2013 Location: Oceanside CA Status: Offline Points: 1556 |
Post Options
Thanks(0)
|
I've got it about as close as I can get to my 10* vacuum advance goal now. I made another plate and ended up 6* advance. Just the slightest touch up on the grinder and I was at 9.5*. I used my vacuum pump to ensure it travelled smoothly through the range and after a slight tweak had it good. The vacuum advance starts at about 6 in.hg and is all in by 11 in.hg. Initial is 14* mechanical plus 9.5* vacuum for 23.5* at 750 RPM idle. I'm pleased with that for now, but I haven't taken a test drive just yet. I'll probably run over to a cars and coffee cruise in tomorrow morning and see how she does.
Here's the first attempt and the second side by side. Here it is in the distributor. The stop arm was bowed up here from the way I wedged it into place causing the breaker plate to bind up slightly. I straightened it all out on final fitment. Here's the scroll saw I cut the aluminum with. My bandsaw cuts a lot more smoothly, but I didn't have a blade on it and this was quick and ready to go. Edited by Red20 - Jul/22/2017 at 12:22am |
|
1969 Javelin SST "Screamin' Banana" - Totaled Feb 2018
1973 Hornet Sportabout X "yellajack" - 360/727/TracLoc DAILY DRIVER |
|
Post Reply | Page <12 |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |