Your donations help keep this valuable resource free and growing. Thank you.
|
Reassembling Moser axles/bearings etc |
Post Reply | Page 12> |
Author | |
1/2astjav
AMC Fan Joined: Apr/07/2011 Location: Puget Sound Status: Offline Points: 21 |
Post Options
Thanks(0)
Posted: Jun/07/2011 at 8:35pm |
I was wondering if anyone else has here has dealt with Moser axles.
The new one piece axles finally got here. I'm familiar on the sequence for the backing plates,outer seal,retainer,and the bearing. There is a thick washer or spacer not sure where it goes???? anyone? I was also told i need to cut some of the outer seal as well. Another mystery..........geeez........ You would think that Moser $$$ would send directions or the guy i had to go through would know. Heh right...... Anyway, Moser is closed till tomorrow and i'm dying to get these in. Thanks for any help. |
|
poormansMACHINE
AMC Addicted Charter Member Joined: Jun/28/2007 Location: Shoemaker-Levy9 Status: Offline Points: 12302 |
Post Options
Thanks(0)
|
Ring is pressed on last after the bearing.
|
|
1/2astjav
AMC Fan Joined: Apr/07/2011 Location: Puget Sound Status: Offline Points: 21 |
Post Options
Thanks(0)
|
Got it, thanks. Anyone know about removing part of the outer seal? I"m gonna go ahead and make an assumption that Moser wont know either................
|
|
bcsideshow
Supporter of TheAMCForum Joined: May/19/2010 Location: Kenosha Status: Offline Points: 1228 |
Post Options
Thanks(0)
|
I just installed a set into my 70 AMX and did not trim anything. X2 what PMM said. Press the bearing on then the spacer ring. Make sure you have the backing plates on the correct sides. |
|
1969 SCRambler "B"
1970 AMX 390 Auto 1968 AMX 390 Auto 1970 Rebel Machine Project 1969 AMX 390 4SPD Project 1969 AMX 390 Auto Project 1969 Javelin 390 project 1997 Cherokee lifted 1998 TJ Lifted |
|
1/2astjav
AMC Fan Joined: Apr/07/2011 Location: Puget Sound Status: Offline Points: 21 |
Post Options
Thanks(0)
|
Yah if you get the plates wrong ............that would be bad........... thankfully i found a decent machine shop that hasn't screwed anything up.......yet although they are such pussses , they dont have the balls to take a swing at helping me re-pin the door hinges, and i mean punch them out with a bigger pin. I tried the kits they had at some of the distributors and guess what..... they suck too. Why are all these people such *$@# heads? all i want to do is get a car on the road, yet i get to listen to these "experts" spout a bunch of crap and dont help, advise, or know what the heck they are taliking about. Seriously, these last 10 years i have had this car i have met some of the coolest AND dumbest People in my life. My question is --- Why be a douche bag??? i just dont get it
|
|
bbgjc
AMC Addicted Joined: Nov/24/2009 Location: No.VA Status: Offline Points: 1660 |
Post Options
Thanks(0)
|
I know which supplier your talking about. They know all and everyone else is wrong. Can't be their products.
Try Galvin's they are great and very helpful. Calling is best. I'd be a little worried that a "machine shop" couldn't set up a hinge to get over bored/reamed and a larger pin installed. You can darn near do at at home with a vise, a piece of pipe and a drill. Man I sure am glad I got two sets of AMC pins and bronze bushing before they disappeared.(Or they seem to have disappeared)
|
|
jeremy0711
AMC Addicted Joined: Dec/12/2008 Location: Southern IN Status: Offline Points: 1547 |
Post Options
Thanks(0)
|
How long did it take you to get your set to you after you had sent in your old axles? I am about to get some myself.
|
|
FuzzFace2
AMC Addicted Joined: Jul/05/2007 Location: Angier, N.C. Status: Offline Points: 10356 |
Post Options
Thanks(0)
|
BTW I did not need to trim any thing to make it all fit.
Dave ----
|
|
TSM = Technical Service Manual
75 Gremlin X v8 for sale 70 Javelin 360/auto drag car 70 Javelin 360/T5 Street car |
|
tsanchez
AMC Addicted Joined: Jul/09/2007 Location: Arizona Status: Offline Points: 4303 |
Post Options
Thanks(0)
|
bcsideshow
Supporter of TheAMCForum Joined: May/19/2010 Location: Kenosha Status: Offline Points: 1228 |
Post Options
Thanks(0)
|
I think they need 2-3 days + shipping time.
|
|
1969 SCRambler "B"
1970 AMX 390 Auto 1968 AMX 390 Auto 1970 Rebel Machine Project 1969 AMX 390 4SPD Project 1969 AMX 390 Auto Project 1969 Javelin 390 project 1997 Cherokee lifted 1998 TJ Lifted |
|
Post Reply | Page 12> |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |