Your donations help keep this valuable resource free and growing. Thank you.
|
Oil and dizzy gear |
Post Reply | Page 123 4> |
Author | |
sasyamx
AMC Addicted Joined: Jul/24/2007 Location: Kentucky Status: Offline Points: 525 |
Post Options
Thanks(0)
Posted: May/15/2015 at 11:00pm |
About how much oil should come out of the dizzy gear , my new motor, running a new rollmaster chain , everything else is factory, has a good drip coming out of the bottom hole and the rest are wet and oozing out but not squirting or anything . Is this about right or does it need to be squirting out like crazy , i did notice some oil coming out behind the fuel pump eccentric , is this good , not alot about a good drip or so and all this was done using a hand drill and about 25 pis most of the time , at 50 psi it was about the same . Thanks
|
|
401MATCOUPE
AMC Addicted Joined: May/20/2010 Location: Salisbury, MD Status: Offline Points: 5367 |
Post Options
Thanks(0)
|
From the last checks I did, lots of oil out between eccentric and gear....lot of oil out of dizzy gear. I'll post link to video later.
Edited by 401MATCOUPE - May/16/2015 at 1:34pm |
|
Ross K. Peterson
68X,GoPac,343,AT,52A(1stCar) 68X,GoPac,390,4sp,52A 69X,GoPac,390,4sp,64A 70X,GoPac,390,4sp,87A,8 70X,GoPac,390,4sp,BBO,8 70 Jav SST,390,AT,BSO 74MatX,401,AT,Prototype 74MatX,401,AT |
|
pipefactory
AMC Nut Joined: Jul/27/2012 Location: Superior, Wi Status: Offline Points: 405 |
Post Options
Thanks(0)
|
mine with the rollmaster did the same thing. While spinning with a drill had 67 psi pumped a fair amount from behind the eccentric and a good amount from the cam gear. That worried me but it was still 67 psi. Maybe rollmaster did it to oil the chain more. My last rollmaster didn't do that but was all stretch out after 75 1/4 mile passes.
Does anyone have a picture of a new one, My old one had 2 small groves cut in it and I think I remembered seeing 4 groves in my new one that is installed. |
|
Face distorting torque
10.99@121 mph |
|
SC397
AMC Addicted Joined: Apr/30/2009 Location: Michigan Status: Offline Points: 5476 |
Post Options
Thanks(0)
|
The newer Rollmaster T-sets have a issue now. They must have changed machining sources hence changing the part. I have tried to contact them about the issue and of coarse no response.
|
|
sasyamx
AMC Addicted Joined: Jul/24/2007 Location: Kentucky Status: Offline Points: 525 |
Post Options
Thanks(0)
|
The new rollmaster does have 4 slots in them now , my old cloyes had 6 i think never had any problems but never check how stuff came out , my old set up had the two piece eccentric this one is a one piece that came with this motor , go under my face book page and you can see the video, just look up Patrick Terrell
|
|
SC397
AMC Addicted Joined: Apr/30/2009 Location: Michigan Status: Offline Points: 5476 |
Post Options
Thanks(0)
|
The slots on the newer Rollmaster have much deeper slots than the old Cloyes. Plus, one slot is exactly where you don't want to be at the transfer slot to the dizzy gear. I weld them all shut except where the key way is regardless of brand.
|
|
401MATCOUPE
AMC Addicted Joined: May/20/2010 Location: Salisbury, MD Status: Offline Points: 5367 |
Post Options
Thanks(0)
|
Here is a link to video on how the oiling should be....65 PSI on gauge, engine not running/rotating. I misread your original post ...yes lots of oil out the between gear...some think too much.
|
|
Ross K. Peterson
68X,GoPac,343,AT,52A(1stCar) 68X,GoPac,390,4sp,52A 69X,GoPac,390,4sp,64A 70X,GoPac,390,4sp,87A,8 70X,GoPac,390,4sp,BBO,8 70 Jav SST,390,AT,BSO 74MatX,401,AT,Prototype 74MatX,401,AT |
|
Rebel Machine
AMC Addicted Joined: Jul/03/2007 Location: Western Il Status: Offline Points: 5122 |
Post Options
Thanks(0)
|
I've got more video of these types of tests if anyone wants to see them.
-Steve- |
|
sasyamx
AMC Addicted Joined: Jul/24/2007 Location: Kentucky Status: Offline Points: 525 |
Post Options
Thanks(0)
|
Mine doesn't have that much running out between the gear and eccentric , but it also don't have that much coming out of the dizzy gear.
|
|
sasyamx
AMC Addicted Joined: Jul/24/2007 Location: Kentucky Status: Offline Points: 525 |
Post Options
Thanks(0)
|
https://www.youtube.com/watch?v=1Ls183KyY_I , hear is a video of what mine dizzy gear oiling is , at 25- 50 psi , mostly 25 psi. Do you all think it's enough ,or should i add a oil line to squirt on it ,hears another video of it and the valley . https://www.facebook.com/patrick.terrell.52/videos/1106314162718953/
|
|
Post Reply | Page 123 4> |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |