Your donations help keep this valuable resource free and growing. Thank you.
|
My 65 440H first build |
Post Reply | Page <1234 19> |
Author | |
AZ65440H
AMC Nut Joined: Mar/05/2012 Location: Phoenix, AZ Status: Offline Points: 308 |
Post Options
Thanks(0)
|
The rear leaf is on sliders but the photos are too large to post. I'll post later.
|
|
HOT IN AZ
|
|
AZ65440H
AMC Nut Joined: Mar/05/2012 Location: Phoenix, AZ Status: Offline Points: 308 |
Post Options
Thanks(0)
|
The rear 15x8 Rocket Igniter rims showed up today..
245/60/15 under the back tight. Shooting for this ride height in the rear.
Edited by AZ65440H - Aug/19/2019 at 11:22am |
|
HOT IN AZ
|
|
AZ65440H
AMC Nut Joined: Mar/05/2012 Location: Phoenix, AZ Status: Offline Points: 308 |
Post Options
Thanks(0)
|
Edited by AZ65440H - Feb/01/2017 at 8:24pm |
|
HOT IN AZ
|
|
AZ65440H
AMC Nut Joined: Mar/05/2012 Location: Phoenix, AZ Status: Offline Points: 308 |
Post Options
Thanks(0)
|
|
|
HOT IN AZ
|
|
AZ65440H
AMC Nut Joined: Mar/05/2012 Location: Phoenix, AZ Status: Offline Points: 308 |
Post Options
Thanks(0)
|
Seems my photos are coming out too large now. I had to center the tank moving the filler neck over a few inches.
Here's the filler neck coming back through the original hole after that small adjustment. Didn't wanna use a fuel cell. Edited by AZ65440H - Nov/12/2016 at 1:49pm |
|
HOT IN AZ
|
|
AZ65440H
AMC Nut Joined: Mar/05/2012 Location: Phoenix, AZ Status: Offline Points: 308 |
Post Options
Thanks(0)
|
|
|
HOT IN AZ
|
|
AZ65440H
AMC Nut Joined: Mar/05/2012 Location: Phoenix, AZ Status: Offline Points: 308 |
Post Options
Thanks(0)
|
Shortened the axle with 9" ends to eliminate the c-clips. Should have it on the ground this week. After the drive lines made I'll pull the trans to get all the clutch, hydraulic through out, n pedals all hooked up. If anyone knows what headers should go in without having to rework them and not hang to low, I'd appreciate all suggestions.
|
|
HOT IN AZ
|
|
AZ65440H
AMC Nut Joined: Mar/05/2012 Location: Phoenix, AZ Status: Offline Points: 308 |
Post Options
Thanks(0)
|
Edited by AZ65440H - Jul/25/2019 at 2:33pm |
|
HOT IN AZ
|
|
AZ65440H
AMC Nut Joined: Mar/05/2012 Location: Phoenix, AZ Status: Offline Points: 308 |
Post Options
Thanks(0)
|
This is my first effort at an amc modification so please let me know if you see anything that I'm doing that should be addressed before I get too far to avoid problems down the line. Ride height is a little higher then I desired on the rear but I'll leave it until I see where the front will sit once I get to it.
Edited by AZ65440H - Nov/12/2016 at 2:00pm |
|
HOT IN AZ
|
|
mitchs66
AMC Nut Joined: Sep/22/2007 Location: Iowa Status: Offline Points: 368 |
Post Options
Thanks(0)
|
Looks really nice. I'm doing mine about the same. Nice work, I'll keep watching.
|
|
Post Reply | Page <1234 19> |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |