Your donations help keep this valuable resource free and growing. Thank you.
|
Old School Ansen Style Mags |
Post Reply |
Author | |
pacerman
Supporter of TheAMCForum Joined: Jul/03/2007 Location: United States Status: Offline Points: 9060 |
Post Options
Thanks(0)
Posted: Jun/19/2017 at 8:49pm |
I have a set of these that I am trying to install as rollers while I get my rally wheels sandblasted and powdercoated, ready for refinishing.
What is the secret to installing the lugnuts? They are straight shank, barely fit through the wheel lug openings and have captive washers. It appears that they would be easy to crossthread on my lugs which are in very good condition. Are the shanks supposed to be greased? anti-seize used? I must have missed the whole aluminum wheel craze in my youth. Joe
|
|
Happiness is making something out of nothing.
|
|
304-dude
AMC Addicted Joined: Sep/29/2008 Location: Central Illinoi Status: Offline Points: 9082 |
Post Options
Thanks(0)
|
A wee trick with blind threading any screw or nut.
Bottom lightly while turning counter clockwise. You should feel a small give as it bottoms in position to be threaded. Then rotate clockwise to thread. Never cross threaded doing that procedure. |
|
71 Javelin SST body
390 69 crank, 70 block & heads NASCAR SB2 rods & pistons 78 Jeep TH400 w/ 2.76 Low 50/50 Ford-AMC Suspension 79 F150 rear & 8.8 axles Ford Racing 3.25 gears & 9" /w Detroit locker |
|
tomj
AMC Addicted Joined: Jan/27/2010 Location: earth Status: Offline Points: 7553 |
Post Options
Thanks(0)
|
i dont care about conventional wisdom -- i lubricate all wheel studs and nuts. i use that silver stuff that turns you into the Tin Man from WIZARD OF OZ no matter how careful you are with it. very little needed.
304-dude's trick is indeed the dung, as the kids say today. or did say, some years ago. ok i'm old. |
|
1960 Rambler Super two-door wagon, OHV auto
1961 Roadster American, 195.6 OHV, T5 http://www.ramblerLore.com |
|
farna
Supporter of TheAMCForum Moderator Lost Dealership Project Joined: Jul/08/2007 Location: South Carolina Status: Offline Points: 19689 |
Post Options
Thanks(0)
|
Silver anti-seize... I use it also, have for years!! Doesn't matter is you use the silver or copper colored anti-seize...
|
|
Frank Swygert
|
|
pacerman
Supporter of TheAMCForum Joined: Jul/03/2007 Location: United States Status: Offline Points: 9060 |
Post Options
Thanks(0)
|
Okay, the main problem is that some of the lug openings in the mags are galled and the correct lug nuts do not fit easily down in to the openings. I understand that the clearances are supposed to be small, but if the lugs don't easily fit they are impossible to thread onto the studs. At any rate, the wheels are only being used to support the car while the rallies are off being refinished. So I am making do with two or three lug nuts on each wheel and not sweating the missing nuts. I have learned that I would never want this type of wheel on any of my cars. I am wondering though about the correct way to lightly clean the holes so the next guy could use the wheels if someone wants them. Joe
|
|
Happiness is making something out of nothing.
|
|
andyleonard
AMC Apprentice Joined: Dec/10/2016 Location: 90290 Status: Offline Points: 138 |
Post Options
Thanks(0)
|
Unless you've got the wrong parts or the wrong bolt pattern, just tape 3-4" of emery cloth to a drill bit and hone out the holes in the wheels. If the lugs are cranked down too hard they will distort the wheel holes and gum things up. Racecar does it all the time.
|
|
pacerman
Supporter of TheAMCForum Joined: Jul/03/2007 Location: United States Status: Offline Points: 9060 |
Post Options
Thanks(0)
|
I got the wheels on the car. Thanks for the tips. I also learned that it helps to measure the diameter of the shanks of the lug nuts. There was about three thousandths of an inch difference in the diameters between the short shank lug nuts and the long shank nuts that I have. I used the long shank nuts which engage more of the threads on the lugs anyway and tossed the oversize short shank nuts because I don't want to go through this again. Joe
|
|
Happiness is making something out of nothing.
|
|
one bad rambler
AMC Addicted Joined: Jan/09/2008 Location: On The Island Status: Offline Points: 2007 |
Post Options
Thanks(0)
|
I glad you got them on ...the key is extended wheel studs
|
|
68 AMX 390 4 Speed,68 American,64 American 2 Door Wagon Altered Wheelbase,78 Concord Build 360,727,8.8
|
|
990V8
AMC Addicted Joined: Oct/07/2016 Location: Gloucestershire Status: Offline Points: 789 |
Post Options
Thanks(0)
|
One problem with anti-seize, indeed about the only problem, is that to an extent it acts as a lube. This throws out the torque reading if one is using a torque wrench. And that of course can lead to things being overtightened.
Main problem I had with alloys back in the day is that if not removed for a long time they can weld themselves to the brake drum. Recall with our Peugeot 205 having to take a sledge and a block of wood to get the rears off. After that I always greased the back of the wheels. Ivor |
|
63 Canadian Ambo 990 V8 327
74 LandRover Lightweight V8 SIII Shopping Trolley |
|
6PakBee
Supporter of TheAMCForum Charter Member Joined: Jul/01/2007 Location: North Dakota Status: Offline Points: 5458 |
Post Options
Thanks(0)
|
I'm a big fan of anti-seize too. I paint the register portion of an alloy wheel with anti-seize to prevent that corrosion attachment. Just an FYI, got problems with corrosion on a battery terminal? Anti-seize is your friend here also. |
|
Roger Gazur
1969 'B' Scheme SC/Rambler 1970 RWB 4-spd Machine 1970 Sonic Silver auto AMX All project cars. Forum Cockroach |
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |