Your donations help keep this valuable resource free and growing. Thank you.
|
Got a fuel sender that works...but |
Post Reply |
Author | |
Gelalthedamned
AMC Nut Joined: Nov/28/2014 Location: Athens ga Status: Offline Points: 376 |
Post Options
Thanks(0)
Posted: Sep/14/2018 at 6:30am |
It’d been 4 years of keeping up with last time I filled up vs how many miles driven since then at about 12 miles to a gallon.
American depot has/had remanufactured sending units for the 73 Gremlin. The gauge works...the seal doesn’t...I lost about 6 gallons in the parking lot at work tigons out. So, is there a trick to put these in an ensure it’s sealed? I’m leaning toward fuel resistant gasket sealer. I installed it dry cause I assumed it was a pressure seal |
|
Calamity - 73 Gremlin X zombie rod (daily driver)
|
|
304-dude
AMC Addicted Joined: Sep/29/2008 Location: Central Illinoi Status: Offline Points: 9081 |
Post Options
Thanks(0)
|
Should work dry if... The seal is thick enough. I think it is twice as thick as a parts counter roll of gasket material.
You can use 3M gasket maker and rubber seal adhesive, but stay away from silicone, had a tank done with it and some of it ended up intermittently clogged at the pickup. Just rub a thin film along the bottom of the seal and place into position on the tank. Then install the sending unit. The seal should be thick enough to cause some need for extra pressure when rotating to the locked in position. You locking tabs my have been knocked out of adjustment when removing the old one. So re-bending into place may be required for snug seal. |
|
71 Javelin SST body
390 69 crank, 70 block & heads NASCAR SB2 rods & pistons 78 Jeep TH400 w/ 2.76 Low 50/50 Ford-AMC Suspension 79 F150 rear & 8.8 axles Ford Racing 3.25 gears & 9" /w Detroit locker |
|
AMXFSTBK390
AMC Addicted Joined: Oct/22/2013 Location: SF Bay Area Status: Offline Points: 3489 |
Post Options
Thanks(0)
|
Yesterday, pulled the 68 AMX tank out of the shed to install it. The ring mounting rubber gasket at the opening to the tank is stuck in place pretty good. Didn't want to disturb it unless vendors sell them. The only rubber gasket for the sending unit to tank flange I could find is a "O" ring type. What type of seal does the Gremlin use? I will use 3M gasket maker as 304-dude suggested if I can't locate a new flat rubber gasket like what I believe to be the original gasket that is on the tank now.
|
|
Questions are powerful tools...what's in your toolbox?
|
|
mmaher94087
AMC Addicted Joined: Apr/01/2008 Location: Arizona Status: Online Points: 1676 |
Post Options
Thanks(0)
|
I can't speak to the Gremlin but the AMX/Javelin seal is a round rubber 'O'-ring.
|
|
Mike
|
|
AMXFSTBK390
AMC Addicted Joined: Oct/22/2013 Location: SF Bay Area Status: Offline Points: 3489 |
Post Options
Thanks(0)
|
Evidently after fifty years under compression the "O" ring goes flat. Also noticed there was no filter (sock). So purchased this eBay stainless fuel sending unit package from a seller who has received 5 of 5 positive reviews. Great price at $43.97.
|
|
Questions are powerful tools...what's in your toolbox?
|
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |