Your donations help keep this valuable resource free and growing. Thank you.
|
196 crank differences |
Post Reply |
Author | |
farna
Supporter of TheAMCForum Moderator Lost Dealership Project Joined: Jul/08/2007 Location: South Carolina Status: Offline Points: 19676 |
Post Options
Thanks(0)
Posted: Feb/12/2019 at 5:52am |
Several people have machined the "volcano" off and run them. No one has mentioned the depth of the pilot hole, maybe they were using auto trannys, but that is something to check when having it machined off. Would be easy to correct while it's in a lathe. The recess isn't for anything specific IIRC. I know for sure the flexplate used on the 196 is flat, and the flywheel has a recess that fits over the hub, IIRC. I think that's just machining marks where the "volcano" is turned off from the factory. These are FORGED cranks -- would be easier to turn it off than to change the forging dies.
|
|
Frank Swygert
|
|
r4238id
AMC Fan Joined: Mar/11/2018 Location: Boise Idaho Status: Offline Points: 18 |
Post Options
Thanks(0)
|
Thanks for updating the links! |
|
tomj
AMC Addicted Joined: Jan/27/2010 Location: earth Status: Offline Points: 7544 |
Post Options
Thanks(0)
|
oops, rats... i had to do some serious updates on my website(s) (they go back to 1994) and intended to preserve URLs, but apparently i broke them. i edited the URLs in the post above; but in general, go to sr-ix.com, click "roadster", evertthing below there should be int he same order. sorry about that! |
|
1960 Rambler Super two-door wagon, OHV auto
1961 Roadster American, 195.6 OHV, T5 http://www.ramblerLore.com |
|
r4238id
AMC Fan Joined: Mar/11/2018 Location: Boise Idaho Status: Offline Points: 18 |
Post Options
Thanks(0)
|
I had some health problems that stalled me on my project but picking this back up and just got the OHV out of the machine shop.
TomJ - I had referenced your links last year and would like to review them again however they appear to no longer be valid. Do you have this info posted in another location?
|
|
tomj
AMC Addicted Joined: Jan/27/2010 Location: earth Status: Offline Points: 7544 |
Post Options
Thanks(0)
|
unless someone comes up with a bellhousing that has an unusual depth, or a T96 with an input shaft much longer than the 7.125, all manual 195.6's have volcano butt cranks. it simply, literally, doesn't otherwise stack up.
if you can make some measurements, i'd love to have them: bellhousing depth, meaning from flat where the trans bolts on to the big surface where it bolts to the motor... here is my rather involved but disorganized notes on this very subject: http://sr-ix.com/Roadster/transmission/index.html and what i'm driving now (T5, not directly applicable to you) http://sr-ix.com/Roadster/transmission/T5research/index.html (repaired URLs, 25 jan 2019) Edited by tomj - Jan/25/2019 at 9:09pm |
|
1960 Rambler Super two-door wagon, OHV auto
1961 Roadster American, 195.6 OHV, T5 http://www.ramblerLore.com |
|
farna
Supporter of TheAMCForum Moderator Lost Dealership Project Joined: Jul/08/2007 Location: South Carolina Status: Offline Points: 19676 |
Post Options
Thanks(0)
|
It's a "volcano" type. Apparently the flat ones weren't across the board until 63. I'm pretty sure the 61 American I had with flat head and manual trans had a flat crank, but that was too many years ago for me to be certain. The cranks will interchange, just need to match the trans/flywheel to the right one. Of course that would mean you couldn't rebuild the crank without having both motors out. Could still bore the block and rebuild the head, just turn crank and install it as the final step. That would save a good bit of time...
|
|
Frank Swygert
|
|
r4238id
AMC Fan Joined: Mar/11/2018 Location: Boise Idaho Status: Offline Points: 18 |
Post Options
Thanks(0)
|
I have a 61 American flathead w/ automatic and a 196 OHV that originated in a 61 Classic with manual transmission. My intention is to continue driving the car while I rebuild the OHV and then make the swap. I am looking for clarification on the crank differences that I may run into. If I have understood some past discussions correctly 62 and earlier auto cranks were the Volcano type and manual were the flat crank. I would expect the American to have a volcano when pulled and the OHV out of the Classic with manual to be flat but as I look at the crank on the OHV it appears to be the "volcano" type. I have attempted to put the picture from the OHV in this post for reference.
|
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |