Your donations help keep this valuable resource free and growing. Thank you.
|
My 1967 AMC Marlin Thread |
Post Reply | Page <1 1213141516 17> |
Author | |||
Rogue343
AMC Addicted Joined: Feb/16/2011 Location: Norwalk, OH Status: Offline Points: 1004 |
Post Options
Thanks(0)
|
||
X2! Looks really good. What paint did you use?
|
|||
1967 Rambler Rogue 'X' code 343 4 speed
1966 Rambler American 440 4 door Factory 290 (now 360) 4 speed VIN 100003 |
|||
67 Marlin
AMC Addicted Joined: Feb/21/2015 Location: Minnesota Status: Offline Points: 877 |
Post Options
Thanks(0)
|
||
Bought it from Galvin's. Advice to those who might want to do the same: if you do the whole motor, I'd plan for at least three cans because it goes on pretty thin. Real nice, but thin. Edited by 67 Marlin - Feb/04/2020 at 8:41pm |
|||
LakesideRamblin
AMC Addicted Joined: Dec/21/2015 Location: So. California Status: Offline Points: 2692 |
Post Options
Thanks(0)
|
||
X3! Love that color. Excellent work.
|
|||
LakesideRamblin
69 Rambler 360 73 Javelin 360 "If you could kick the person in the pants responsible for most of your trouble, you wouldn't sit for a month." T. Roosevelt |
|||
67 Marlin
AMC Addicted Joined: Feb/21/2015 Location: Minnesota Status: Offline Points: 877 |
Post Options
Thanks(0)
|
||
The 343 came alive like Peter Frampton! 417 peak TQ @ 3700 RPM with 90% of peak from 2800 to 5100. 363HP @ 5000 with 90% of peak HP from 4200 to 5200. The AFR was a little on the rich side, wonder what a run at 12.5 or a little leaner would have done, but sure makes lots of power in the middle where I wanted it. 2023 Update: The 343 now has an RPM Air Gap intake with a one-inch spacer (most that would fit under the hood) and custom Mark Whitener 750 double-pumper. I would say there is at least a 30 HP and TQ increase over the custom 390 intake and Edelbrock AVS2 carb that I had on at the time of the dyno. That carb gave the engine shop fits. They told me to use a Holley, but no, I wanted the original AMC look. Glad I went to the Holley setup! I'd say 20 was the carb and 10 was the intake. This thing gets up to 6000rpm very quickly! Edited by 67 Marlin - Dec/30/2023 at 11:37pm |
|||
george w
Supporter of TheAMCForum Joined: Jan/27/2013 Location: New Jersey Status: Offline Points: 2899 |
Post Options
Thanks(0)
|
||
You've got some nice numbers there !
|
|||
Long time AMC fan. Ambassador 343, AMX 390, Hornet 360, Spirit 304 and Javelin 390. All but javelin bought new.
|
|||
67 Marlin
AMC Addicted Joined: Feb/21/2015 Location: Minnesota Status: Offline Points: 877 |
Post Options
Thanks(0)
|
||
Should have the motor in next week! Going through parts and forgot I cleaned up the accelerator linkage over the winter. I believe the rods were originally painted black and the brackets were natural; I think the whole setup looks snazzier just cleaned up and cleared. Like the new felt washer? It's for a drum set; Ludwig part number P39061P. Edited by 67 Marlin - Dec/31/2023 at 3:57pm |
|||
fhpdave
AMC Nut Joined: May/09/2014 Location: Galena Ohio Status: Offline Points: 445 |
Post Options
Thanks(0)
|
||
Looking great, and those are some nice numbers on your engine. I fot one like seeing another big car being redone.
|
|||
Old enough to know better - young enough not to care
|
|||
67 Marlin
AMC Addicted Joined: Feb/21/2015 Location: Minnesota Status: Offline Points: 877 |
Post Options
Thanks(0)
|
||
Along with the motor rebuild and performance upgrades, some important stuff needed to be done. The calipers and pads on the front and drum kits on the back to help slow down, new brake lines and hoses, replaced the emergency brake, too, and new power steering lines. And, all that safety-minded stuff led back to performance. In the process, found out the rear axle was spun, so now there are new Moser one-piece axle shafts, and they've been pinned to the housing just like downtown!
Edited by 67 Marlin - Dec/31/2023 at 5:22pm |
|||
67 Marlin
AMC Addicted Joined: Feb/21/2015 Location: Minnesota Status: Offline Points: 877 |
Post Options
Thanks(0)
|
||
The Marlin is back on the road, upgraded, and safer than ever. it's downright explosive up to 6000 just like I wanted, too! Edited by 67 Marlin - Dec/31/2023 at 5:20pm |
|||
amcenthusiast
AMC Addicted Joined: Jul/02/2012 Location: SW Atlanta GA Status: Offline Points: 1778 |
Post Options
Thanks(0)
|
||
Oh yeah... looks excellent; love that copper color in the red engine bay.
|
|||
443 XRV8 Gremlin YouTube video: https://www.youtube.com/watch?reload=9&v=2DmFOKRuzUc
XRV8 Race Parts website: http://amcramblermarlin.1colony.com/ |
|||
Post Reply | Page <1 1213141516 17> |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |