Your donations help keep this valuable resource free and growing. Thank you.
|
m12 shift kit |
Post Reply | Page <1234 6> |
Author | |
Javelin69
AMC Apprentice Joined: Dec/11/2013 Location: Madison wi Status: Offline Points: 187 |
Post Options
Thanks(0)
|
I'd be interested in that kit. My amx shifts ok in drive except fairly early up shifts. In manual mode, 1-2 is right now but 2-3 takes forever. I pulled the valves and polished them and cleaned out the bores. I never was quite sure if the springs were in the right location. I also adjusted pressure as shown in the tsm. As I recall some are similar and I couldn't tell from the tsm exactly what goes where. I think this trans has been rebuilt and I wonder if a check ball was left out somewhere or if those springs are in the right spot or maybe weak. Any pointers are welcome.
|
|
george w
Supporter of TheAMCForum Joined: Jan/27/2013 Location: New Jersey Status: Offline Points: 2899 |
Post Options
Thanks(0)
|
Let's assume that you reassembled the valve body correctly. If the transmission seems to upshift too early then the thing to do is to start increasing the pressure by cranking in the set screw in the vacuum modulator a few turns at a time. This does two things. First it raises the shift points and second it increases the line pressure for firmer shifts. Stop when you reach the shift points you're comfortable with. If you go too far the trans. will either shift up way late or not at all. The adjustment screw is not completely linear. It takes more turns initially to move the shift point up and as you raise the pressure further the adjustment becomes more sensitive. The 2-1 closed throttle coast down downshift point will also get raised so you'll find that it will somewhat noticeable when it occurs.
|
|
Long time AMC fan. Ambassador 343, AMX 390, Hornet 360, Spirit 304 and Javelin 390. All but javelin bought new.
|
|
69 ambassador 390
Supporter of TheAMCForum Joined: Nov/22/2009 Location: Peoria, AZ Status: Offline Points: 3539 |
Post Options
Thanks(0)
|
Take weight off the governor fly weight with a grinder. This will help raise the shift points also. Make sure you have the correct manual valve with the extra blocking ring on the shuttle. Thhe one from column shifted cars will eventually upshift no matter where you have the shifter but the floor shift valve will hold first and second as long as you do or the engine blows.
|
|
Steve Brown
Algonac, Mi. 69 Ambassador sst 390 84 Grand Wagoneer 69 Cougar XR7 65 Fairlaine 500XL 79 F-350 Super Camper Special |
|
tumbleweed
AMC Apprentice Joined: Jan/02/2013 Location: odessa tx Status: Offline Points: 206 |
Post Options
Thanks(0)
|
I want a shift kit.hopfully it gets reproduced like the str-11 put me down for one
|
|
Javelin69
AMC Apprentice Joined: Dec/11/2013 Location: Madison wi Status: Offline Points: 187 |
Post Options
Thanks(0)
|
Any thoughts on the lazy 2-3 manual shift? No matter the throttle opening or road speed moving the lever from 2-D results in a shift several seconds after. Curious thing is that the kick down 2-3 shift happens as soon as the pedal is lifted. Part throttle 2-3 in drive seems ok. Actually this is more of my concern than the low shift points.
Edited by Javelin69 - Mar/08/2014 at 9:08am |
|
amc67rogue
AMC Addicted Joined: Nov/05/2008 Location: Phx. AZ. Status: Offline Points: 1578 |
Post Options
Thanks(0)
|
I remember a road test of the S/C 360 hornet and the test driver short shifted the 2-3 shift to allow for the delay.
|
|
Keith Coggins 67Rogue X code
|
|
69 ambassador 390
Supporter of TheAMCForum Joined: Nov/22/2009 Location: Peoria, AZ Status: Offline Points: 3539 |
Post Options
Thanks(0)
|
That is normal shifting. You haven't reached the full throttle shift point yet. 1-2 is instant and 2-3 will happen when programmed because you have put It back in normal drive. If you want instant 2-3 at low rpms, you need to modify the valve body to have full manual control and no automatic options. That is NOT a shift kit function with any make of shift kit. A full manual kit is what you want.
If you want to help the trans shift a little before the full throttle downshifted point, you will need to eliminate the downshift input signal to the solenoid. You can just unplug the wire at the trans or pedal or install a disable switch inline. Edited by 69 ambassador 390 - Mar/08/2014 at 11:02am |
|
Steve Brown
Algonac, Mi. 69 Ambassador sst 390 84 Grand Wagoneer 69 Cougar XR7 65 Fairlaine 500XL 79 F-350 Super Camper Special |
|
Javelin69
AMC Apprentice Joined: Dec/11/2013 Location: Madison wi Status: Offline Points: 187 |
Post Options
Thanks(0)
|
The lazy shift is at any road speed even over the 2-3 programmed shift and even at light throttle at that speed.
|
|
69 ambassador 390
Supporter of TheAMCForum Joined: Nov/22/2009 Location: Peoria, AZ Status: Offline Points: 3539 |
Post Options
Thanks(0)
|
It's not lazy. You are switching from manual mode to Drive/Auto when you move the shifter to Drive. If it is late or ties up at the 2-3 shift, then you have an issue. May be an accumulator function or leaking check valve or bad seals.
|
|
Steve Brown
Algonac, Mi. 69 Ambassador sst 390 84 Grand Wagoneer 69 Cougar XR7 65 Fairlaine 500XL 79 F-350 Super Camper Special |
|
348AMX
AMC Addicted Joined: Jul/03/2007 Location: Massachusetts Status: Offline Points: 4165 |
Post Options
Thanks(0)
|
a reproduction shift kit would be well appreciated and probably popular/sell well. But you should also reproduce a band kit with modern friction material to go with it.
|
|
Post Reply | Page <1234 6> |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |