Your donations help keep this valuable resource free and growing. Thank you.
|
232 exhaust manifold broken!!! |
Post Reply | Page 12> |
Author | |
oxide80
AMC Apprentice Joined: Sep/15/2010 Location: Maine Status: Offline Points: 86 |
Post Options
Thanks(0)
Posted: May/30/2012 at 10:17am |
Already PMed Doc thanks for your input!
|
|
billd
Moderator Group Forum Administrator Joined: Jun/27/2007 Location: Iowa Status: Offline Points: 30894 |
Post Options
Thanks(0)
|
I think this is his answer - Doc can probably help with parts - and he'll be reasonable.
|
|
DocCreer
AMC Addicted Joined: Oct/03/2009 Location: Portland Oregon Status: Offline Points: 1568 |
Post Options
Thanks(0)
|
i got 232 intake and exhuast manifolds in good shape ill let go for very cheap...PM me.
|
|
61 American
82 eagle limited |
|
billd
Moderator Group Forum Administrator Joined: Jun/27/2007 Location: Iowa Status: Offline Points: 30894 |
Post Options
Thanks(0)
|
starting in about 1981 AMC switched to a "divorced" manifold pair. The exhaust was made more sweeping, more like tubes, but still cast, and not connected to the intake.
The intake was changed to aluminum with a ceramic heater under the bottom which ran until the engine temp reached 165 degrees, then the water warmed the intake. So 81+ was heated by an electric heater, then water, while prior it was the exhaust gases and the heat-riser valve that heated the intake. |
|
oxide80
AMC Apprentice Joined: Sep/15/2010 Location: Maine Status: Offline Points: 86 |
Post Options
Thanks(0)
|
Its an old crack, someone had it apart at some point long before I bought the car, there was an exhaust gasket in place, im sure it was just the stress of heatin/cooling and torque. What's the difference on the 80number and new manifolds?
|
|
billd
Moderator Group Forum Administrator Joined: Jun/27/2007 Location: Iowa Status: Offline Points: 30894 |
Post Options
Thanks(0)
|
I've seen 4.0 exhaust cracked from that stress as well.
My Jav never had such support, never broke a manifold, either, though. Your breakage is not very likely to be due to the stress of a hanging pipe, however. Reason I suggest that is that it's the number 1 end broken off - it's not broken in the middle - the pipe weight and load should have never reached that far front end. Because it's a far front or far rear end it's probably due to improperly being torqued at some point. Although they can and do break "on their own", it's VERY unlikely, and in each case I've seen it was after some past service. (#1 and #6 are almost always because of heating and cooling stresses - expanding and contracting against the bolts) If the end bolts are tightened too tight, or the bolts are tightened out of sequence, the natural expansion and contraction of the LONG chunk of cast will cause it to break. I've seen a lot of 6's of other makes do it as well. You are lucky that they should be the same for 232 and 258 up through 1980 if I recall correctly. |
|
pacerman
Supporter of TheAMCForum Joined: Jul/03/2007 Location: United States Status: Offline Points: 9057 |
Post Options
Thanks(0)
|
Many years of 199/232/early 258 manifolds will fit. One caution is that you should make sure the exhaust pipe and the rest of the exhaust system is properly supported so the full weight of the exhaust system is not hanging off of the exhaust manifold. This can stress it and cause it to crack or break. The Rambler Americans had a support flange welded onto the exhaust pipe for this purpose. I'm sure it was a weakness AMC found when the were designing the cars. Joe
|
|
Happiness is making something out of nothing.
|
|
oxide80
AMC Apprentice Joined: Sep/15/2010 Location: Maine Status: Offline Points: 86 |
Post Options
Thanks(0)
|
Ok so the #1 exhaust port is completely broken off, what. Years or models will fit? New or used.
Edited by oxide80 - May/29/2012 at 9:49am |
|
oxide80
AMC Apprentice Joined: Sep/15/2010 Location: Maine Status: Offline Points: 86 |
Post Options
Thanks(0)
|
I know anything is possible, but how prone are these for breaking manifold bolts off in the head?
|
|
KermitDRambler
AMC Addicted Joined: Jul/06/2007 Location: Cincinnati, OH Status: Offline Points: 2579 |
Post Options
Thanks(0)
|
Here's a link to info from a TSB that talks about the gaskets and how to put it back together so it doesn't leak: http://www.mattsoldcars.com/RestoreAmerican/loose_intake.shtml
Matt
|
|
Post Reply | Page 12> |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |