Your donations help keep this valuable resource free and growing. Thank you.
|
Amx Quarter |
Post Reply | Page 12> |
Author | |
348AMX
AMC Addicted Joined: Jul/03/2007 Location: Massachusetts Status: Offline Points: 4165 |
Post Options
Thanks(0)
Posted: Oct/13/2012 at 1:23pm |
No worries man thanks.
|
|
AmcKidd
AMC Addicted Charter Member Joined: Jun/29/2007 Location: Oroville, Ca Status: Offline Points: 809 |
Post Options
Thanks(0)
|
passenger side is what i needed, along with the tail panel
|
|
Oroville, Ca
|
|
348AMX
AMC Addicted Joined: Jul/03/2007 Location: Massachusetts Status: Offline Points: 4165 |
Post Options
Thanks(0)
|
How much did that rear clip set you back?? Do you still have the passenger rear quarter section?
Edited by 348AMX - Oct/13/2012 at 12:24pm |
|
Green AMX
AMC Addicted Joined: Feb/16/2012 Location: Florida Status: Offline Points: 521 |
Post Options
Thanks(0)
|
Use a spot weld cutter, strip off the paint at all the factory seams it will make it easy to see the spot welds, center punch or use a 1/8 drill to leave a small dimple in the center of each weld then cut with the spot weld cutter use a slow speed and stay square. Some tool vendors have a hardened flat bar that can be tapped with a hammer thru the seam after you drill out the spot welds to help separate the panels. You also may find some spot that are brazed you will need to cut with a cut off wheel.
|
|
69 AMX 390 4speed go pack
72 Javelin 360 auto(sons) 82 Spirit (wife's 1st car)still not done |
|
69BBB3904spAMX
AMC Addicted Charter Member Joined: Jun/29/2007 Location: San Jose, CA Status: Offline Points: 2761 |
Post Options
Thanks(0)
|
Save those pillar post pieces, the s.s. pieces behind the quarter windows, the roof, etc. I've previously sold all these parts to members that needed these parts
|
|
37 Ford Tudor 60 hp V8 flathead, all original, never restored
69BBB3904spAMX 70 Camaro 1st car 74 Hornet Hatch 6 cyl floor/auto 2007,2008,2009 PT Cruisers Aluminum Deck Car Trailer |
|
AmcKidd
AMC Addicted Charter Member Joined: Jun/29/2007 Location: Oroville, Ca Status: Offline Points: 809 |
Post Options
Thanks(0)
|
well, the filler has rust in the left side window area,trunk lid is rotten on the lower edge, and the tweeks cut the floors very badly- but i may have a extra left quarter when im done
|
|
Oroville, Ca
|
|
69BBB3904spAMX
AMC Addicted Charter Member Joined: Jun/29/2007 Location: San Jose, CA Status: Offline Points: 2761 |
Post Options
Thanks(0)
|
As Mike said, if you use a spot weld cutter to carefully disassemble your donor 1/2 of an AMX, you will end up with parts you don't need that you can resell; passenger qtr, roof, panel under rear window, trunk section, floor sections....
|
|
37 Ford Tudor 60 hp V8 flathead, all original, never restored
69BBB3904spAMX 70 Camaro 1st car 74 Hornet Hatch 6 cyl floor/auto 2007,2008,2009 PT Cruisers Aluminum Deck Car Trailer |
|
AmcKidd
AMC Addicted Charter Member Joined: Jun/29/2007 Location: Oroville, Ca Status: Offline Points: 809 |
Post Options
Thanks(0)
|
the part that im questioning is in the door jamb- there are 3 parts- door jamb, quarter, latch support, the edge of quarter is sandwiched between the other 2
the jamb is undamaged, wont know about wheel house until i pull quarter- i know the drop is gone, and tail light panel will also be replaced at same time i will remove filler and use factory seam in roof LOL... changing my mind isnt an option- this old dog WILL live to bark again- i have a 401/t-5 slated to fill its needs
|
|
Oroville, Ca
|
|
mmaher94087
AMC Addicted Joined: Apr/01/2008 Location: Arizona Status: Offline Points: 1691 |
Post Options
Thanks(0)
|
Buy a spotweld cutter or use a 1/4" drill. Spend a day cutting all the factory welds. In trunk at drop; around the quarter cap area and trunk lip; underside of the wheel opening unless you need the wheel tub and along the door jamb. If the jamb is straight, the skin wraps over the jamb by about 1/2" at the edge of the jamb. If not, then it's a whole nuther ball-game. It's your decision on how much roof material you need to leave. There is a spotwelded and leaded seam from the top of the quarter glass over to the backglass. It's not fun but it can be done. Mike Ps. You'll need to perform surgery twice; once on your car; once on the doner. Oh, start with the doner first incase you change your mind. M
|
|
Mike
|
|
AmcKidd
AMC Addicted Charter Member Joined: Jun/29/2007 Location: Oroville, Ca Status: Offline Points: 809 |
Post Options
Thanks(0)
|
let me preface by saying, 20 years ago i woulda parted this out SOOO fast....
|
|
Oroville, Ca
|
|
Post Reply | Page 12> |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |