Your donations help keep this valuable resource free and growing. Thank you.
|
Engine mystery???? |
Post Reply | Page 123 6> |
Author | |
hpva
AMC Apprentice Joined: Apr/25/2009 Location: Kinderhook,NY Status: Offline Points: 146 |
Post Options
Thanks(0)
Posted: Mar/07/2012 at 6:02pm |
Last year I had the engine rebuilt in my 59 American(196 L head).I put about 800 miles on it and decided to rebuild the carburetor since it didn`t idle as smooth as I thought it should. This October my friend rebuilt the carb and I reinstalled it ,the car ran good for a day.The next day I took it for a drive and it started to buck and sputter I had all I could do to get it back to my garage with a top speed of only 20 mph.After a month of fustration I bought a carburetor on ebay and installed it on the car and as soon as I took it for a test drive I started to have the same problem,bucking stalling and loss of power.Now I`m really confused and last week I bought a remanufactured carb from a place in California they set the choke and all the ajustments so its a bolt on and go.You guessed it after i installed it yesterday I took it for a drive and it idled and drove great for a half mile then started doing the same thing again.Today after some thought I started to think it may be a fuel pump problem but before I check the flow out of the pump I decided to plug the vacuum line that goes from the fuel pump to the vaccum operated wipers.Again I did a test drive and lo and behold the car ran and idled great,I drove it for about half an hour and 5 miles with zero problems.I plan on driving it tomorrow to see if it acts up.Could this be the answer has anyone else ever had a problem like this?Does anyone have a theory or an answer to this?
|
|
farna
Supporter of TheAMCForum Moderator Lost Dealership Project Joined: Jul/08/2007 Location: South Carolina Status: Offline Points: 19611 |
Post Options
Thanks(0)
|
Sounds like you found the problem. Check the vacuum line from the pump to the wiper motor. If it's rubber just replace it. They get old and don't seal very good. The wiper motor itself could have a leak. You can get it rebuilt for under $100 by Peter Stathes (www.amcrambler.com). Cheaper than converting to electric, and it should be good for another 40-50 years.
|
|
Frank Swygert
|
|
hpva
AMC Apprentice Joined: Apr/25/2009 Location: Kinderhook,NY Status: Offline Points: 146 |
Post Options
Thanks(0)
|
Well the car ran fine for three days,today when I took it out it started bucking again.Every time I stepped on the gas it it would act as if it was running out of fuel but put it in park and it would idle ok.Could it be a failing fuel pump,the gas tank is clean and it has a new fuel filter also.I`m running out of ideas .
|
|
gtoman_us
Moderator Group Joined: Jul/10/2007 Location: E. Nebraska Status: Offline Points: 3859 |
Post Options
Thanks(0)
|
Sure sounds like a fuel pump.
|
|
Moderator - Emeritus
Used to collect trophies, now I collect gas receipts and put on miles 1964 Rambler Ambassador Cross Country Wagon 1965 GTO 1931 Model A original survivor "Flat Roofs are Cool" |
|
farna
Supporter of TheAMCForum Moderator Lost Dealership Project Joined: Jul/08/2007 Location: South Carolina Status: Offline Points: 19611 |
Post Options
Thanks(0)
|
The wiper leak could have been in the diaphragm of the fuel/vacuum pump. So the pump is the most likely culprit at this point. sometimes one of the diaphragms go, but the other is usually close behind it.
|
|
Frank Swygert
|
|
maximus7001
Supporter of TheAMCForum Joined: Jun/27/2011 Location: Winnipeg,Canada Status: Offline Points: 1080 |
Post Options
Thanks(0)
|
Sounds like maybe the timing advance is sticking sometimes.
|
|
1968 Javelin SST
1997 GMC Safari AWD 2001 Daewoo Nubira SX (Winnipeg only model) 1997 Honda Accord EX (Canadian Model) Winnipeg, home of the Jets. |
|
59ramblersuper6
AMC Nut Joined: Nov/19/2007 Location: Delaware Status: Offline Points: 337 |
Post Options
Thanks(0)
|
I would suspect a clogged fuel filter. I would replace it with a clear one. I have a 59 classic with the original tank. I cleaned it out real well (MEK, Marine Clean) but at this point I think the lead lining is gone and surface rusts is an issue. Right now I'm changing the fuel filter every hour of running or 60 miles. It will clog with rust and block flow to the electric fuel pump. If you get a see-through one (Spectra, Pep Boys, it has a replaceable filter) you can rule out any fuel supply problems.
|
|
farna
Supporter of TheAMCForum Moderator Lost Dealership Project Joined: Jul/08/2007 Location: South Carolina Status: Offline Points: 19611 |
Post Options
Thanks(0)
|
There never was a lead lining. Gas tanks are bare metal inside (well, many are plastic now). There could still be residue from old gas, but the cleaning should have taken care of that. What you need now is a liner to seal the metal and stick the rust down. It should eventually clean out, but doing it like you are could take a while.
Pull the tank and stick a handful of gravel or 3/8" nuts (any odd ones will do, or a short piece of chain) in there. Put in a little water and shake it around as best you can. That loosens all the rust. Wash out real good and let dry. Then get some liner. I use Hirsch Auto tank sealer, but Eastwood sells a sealer that's about the same. DO NOT use the POR-15 liner! It's a polyurethane. If you don't have 100% coverage fuel can get behind the lining and cause it to separate from the metal. The Hirsch/Eastwood stuff is really thin and won't separate. I used a POR-15 kit once, never again! It might work fine with 100% coverage, but that's hard to ensure inside a tank. The 20 gallon kit left a few uncovered spots in my 18 gallon tank. I've used the Hirsch stuff with no such problems, three cars and four motorcycles. |
|
Frank Swygert
|
|
Thikstik
AMC Addicted Joined: Mar/20/2008 Location: Alabama Status: Offline Points: 1327 |
Post Options
Thanks(0)
|
have u checked the fuel tank lines? and hoses?
|
|
75 gremlin x, jeep 4.0 headed 258,
264H Cliff cam, intake,header. 390 holley. I want a 282 VAM motor! AC/PS/PDB. 72 AMX , 304 2bbl, 3speed, now disks...probably will sell, want an automatic /AC. |
|
Pdok
Supporter of TheAMCForum Joined: Apr/03/2011 Location: Alabama Status: Offline Points: 1021 |
Post Options
Thanks(0)
|
Something sticking in the needle/seat? Had similar issues with a bit of crud in my truck fuel system, but sharp tapping on the Holley cleared the stuff out. You could also just have a moderately failed fuel pump, putting out low volume, enough to fill the bowl at idle. Restricted flow or clogs give the same thing, but no way to know unless you go through the whole system and pull lines and check. Does it happen when the fuel level in the tank is very low, like it could be sucking up some grunge from bad gas? You said the tank was cleaned, tho. The kit was less than $75, and I did it all in a few days with cure/dry time.
Edited by Pdok - Mar/13/2012 at 9:40pm |
|
76 Grem X 258/904,4.0 head/MPFI, Comp X250H cam, Hughes springs, Clifford header, serpentine swap.
|
|
Post Reply | Page 123 6> |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |