Your donations help keep this valuable resource free and growing. Thank you.
|
Removing Pilot Bushing |
Post Reply | Page <1234> |
Author | |
SKeown
AMC Addicted Joined: Jul/30/2009 Location: Texas Status: Offline Points: 3085 |
Post Options
Thanks(0)
|
Go to O'reilys and borrow their pilot bearing removing slide hammer. That's the ideal approach.
SKeown
|
|
Peter Marano
Supporter of TheAMCForum Joined: Jul/01/2007 Location: Kenosha WI Status: Offline Points: 1650 |
Post Options
Thanks(0)
|
I have used newspaper soaked with water, less mess.
|
|
Aljav
AMC Addicted Joined: Jul/18/2007 Location: Wisconsin Status: Offline Points: 1037 |
Post Options
Thanks(0)
|
Wow this is the most reponses I have ever gotten for a question...LOL
Thanks they are all good and should work great..
Now I just have to get the GM bushing to fit in the crank.. and dial in the lakewood bellhousing.... get the shifter in the correct location.... have a drive shaft made.. figure out the cross member to hold up a GM T-10....
Thanks...
Allan
|
|
69 AMX 9.86 132 mph 71 JAV/AMX and 69 Javelin, .. NAMDRA member #1106
|
|
jeremy0711
AMC Addicted Joined: Dec/12/2008 Location: Southern IN Status: Offline Points: 1547 |
Post Options
Thanks(0)
|
my buddy called me up cause he ripped up the tool to remove the bearing and I told him of the good ol grease method and he thought i was nuts but he got it out in 5 minutes compared to the last two hours with the tool.
|
|
Aljav
AMC Addicted Joined: Jul/18/2007 Location: Wisconsin Status: Offline Points: 1037 |
Post Options
Thanks(0)
|
Thats what I was thinking that after 42 years in there it might be a bit tough to remove!!
|
|
69 AMX 9.86 132 mph 71 JAV/AMX and 69 Javelin, .. NAMDRA member #1106
|
|
tyrodtom
AMC Addicted Joined: Sep/14/2007 Location: Virginia Status: Offline Points: 6214 |
Post Options
Thanks(0)
|
Really guys, bread works better than grease.
|
|
66 American SW, 66 American 2dr, 82 J10, 70 Hornet, Pound, Va.
|
|
SKeown
AMC Addicted Joined: Jul/30/2009 Location: Texas Status: Offline Points: 3085 |
Post Options
Thanks(0)
|
Gelled K-Y jelly is an old stand by too.
SKeown
|
|
Rebel 327
AMC Addicted Joined: Feb/04/2009 Location: Ohio Status: Offline Points: 596 |
Post Options
Thanks(0)
|
QUOTE:"Really guys, bread works better than grease"
Wheat, white or Rye? Never heard that but makes sense--may give it a try next time. THX.
|
|
Rebel 327 4-speed
|
|
401cj7jeep
AMC Apprentice Joined: May/07/2010 Location: NW Missouri Status: Offline Points: 84 |
Post Options
Thanks(0)
|
Fill the hole with grease till its spooging out. Then find a bolt or rod or something that fits inside of the bushing. Smake it with a hammer. The grease compressed and forces the bushing out. It probably will take a few swings and packing more grease in the hole each time....
works for me every time...
|
|
78 CJ7, 304, np435, dana 300 twin stick, f/w 9 inch 4.10 spool, f/w dana 44 4.10 welded, 4.5 lift springs, spring over.
|
|
FuzzFace2
AMC Addicted Joined: Jul/05/2007 Location: Angier, N.C. Status: Offline Points: 10356 |
Post Options
Thanks(0)
|
I used wheel bearing grease and a wooden dowel. It took me longer to grind it down on the bench grinder to fit the bushing than it took to get it out. If I was to use bread I would use 12 grain……its healthier for you Dave ---- |
|
TSM = Technical Service Manual
75 Gremlin X v8 for sale 70 Javelin 360/auto drag car 70 Javelin 360/T5 Street car |
|
Post Reply | Page <1234> |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |