Your donations help keep this valuable resource free and growing. Thank you.
|
"New Pertronix Ignitor III Done" |
Post Reply | Page <12345 7> |
Author | |
PHAT69AMX
AMC Addicted Joined: Jul/07/2007 Location: West Virginia Status: Offline Points: 5919 |
Post Options
Thanks(0)
|
Thanks for all the effort TorqueyAMX. Sure you've heard the old saying
" 95% of Carburetor problems are Ignition problems "
|
|
amx39068
Supporter of TheAMCForum Joined: Feb/21/2008 Location: Arizona Status: Offline Points: 11576 |
Post Options
Thanks(0)
|
Amen to that. My worst "carb bog" ever was actually caused by a worn set of points!
|
|
Dan Curtis-Owner and CEO AZ AMC Restorations; Facebook: https://www.facebook.com/amcmusclecars/ & Curtis Real Estate Development
|
|
billd
Moderator Group Forum Administrator Joined: Jun/27/2007 Location: Iowa Status: Offline Points: 30894 |
Post Options
Thanks(0)
|
And my hesitation was solved with 2-3 more degrees of initial advance............ not that the carb doens't need work, it does. But it is no longer embarrassing from a stop light.
TOO FEW folks know how to use and read a scope. Anyone with these cars should get familiar with that pattern and WHAT it means.
You can even diagnose fuel problems if you get really good with a scope.
Scope and vacuum gauge will tell you most anything you need to know about an engine and its condition.
|
|
poormansMACHINE
AMC Addicted Charter Member Joined: Jun/28/2007 Location: Shoemaker-Levy9 Status: Offline Points: 12302 |
Post Options
Thanks(0)
|
Like this?
|
|
billd
Moderator Group Forum Administrator Joined: Jun/27/2007 Location: Iowa Status: Offline Points: 30894 |
Post Options
Thanks(0)
|
Dude - TOO much time on your hands! LOL
|
|
TorqueyAMX
AMC Addicted Joined: Dec/16/2008 Location: Simi Valley CA Status: Offline Points: 1139 |
Post Options
Thanks(0)
|
It's been a learning process with the new unit. Pertronix has alway been good to me over the years with new products showing up at the door. When the new module showed up, must have gone through a half a tank of gas testing with different components and different voltage levels. It was also nice for them to redesign the unit itself so it would work with AMC distributors. I wanted to know exactly how it would work at different levels so folks could make the right choice based on their application and what they want their car to do. If they make the right choice, chances are they will never be dissappointed in the product and they'll still have hair on their head from not pulling it out.
Yesterday Pertronix went over to Speedomotive to do a little testing on a 500 plus HP Chevy small block. They ran baseline pulls on the engine with an MSD Pro Billet Distributor with an HVC Coil and a 7 Series ignition box. They then switched to their Ignitor III Billet Distributor and Flamethrower III coil and NO box and picked up nearly 10 HP. Not something you'd notice but it's there. He also toyed around with the voltage adding some resistors to see the effect and the numbers started dropping way off. Gots to have the juice to cut it loose!
Edited by TorqueyAMX - May/05/2009 at 8:58am |
|
|
|
billd
Moderator Group Forum Administrator Joined: Jun/27/2007 Location: Iowa Status: Offline Points: 30894 |
Post Options
Thanks(0)
|
Do we have a pricepoint yet?
It's something I'd seriously consider.......
I'd even post scope patterns LOL - so ron can pick on me again.......
|
|
amx39068
Supporter of TheAMCForum Joined: Feb/21/2008 Location: Arizona Status: Offline Points: 11576 |
Post Options
Thanks(0)
|
So are these little gems now available for purchase?
|
|
Dan Curtis-Owner and CEO AZ AMC Restorations; Facebook: https://www.facebook.com/amcmusclecars/ & Curtis Real Estate Development
|
|
TorqueyAMX
AMC Addicted Joined: Dec/16/2008 Location: Simi Valley CA Status: Offline Points: 1139 |
Post Options
Thanks(0)
|
Bill,
I'll get a price today and post it. I just don't know. My cost has been the gas to take my distributor out to Pertronix and the gas to test it! "Ouch"!
|
|
|
|
TorqueyAMX
AMC Addicted Joined: Dec/16/2008 Location: Simi Valley CA Status: Offline Points: 1139 |
Post Options
Thanks(0)
|
Yes Dan they are available now. I would suggest trying to order it straight from Pertronix at this point. The unit part no. 71181 was JUST redesigned to work with both AMC and GM Delco distributors. Only about 30 units went out into the market with the previous design. The key in the correct unit is the adaptor plate that is shown.
|
|
|
|
Post Reply | Page <12345 7> |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |