![]() |
Your donations help keep this valuable resource free and growing. Thank you.
|
bendix ????? |
Post Reply ![]() |
Author | |
ditdit ![]() Supporter of TheAMCForum ![]() ![]() Joined: Dec/30/2007 Location: South Carolina Status: Offline Points: 62 |
![]() ![]() ![]() ![]() ![]() Posted: Jul/11/2018 at 2:17am |
I have been told that there are 2 bendix's used for most AMC/Ford type starters ,one has 9 teeth and the other has 10 teeth , my question is witch one is for the V-8 engine , I think I may have a wrong starter in my V-8 as when it starts it sounds like an organ grinder.any help please
|
|
1968 AMX 401/727
1984 Eagle 4.0 org owner 1988 Eagle (time machine) 1980 Jeep J10 1977 Hornet AMX (Green)(sold) |
|
![]() |
|
vinny ![]() Supporter of TheAMCForum ![]() Joined: Jan/05/2012 Location: Calgary Status: Offline Points: 2395 |
![]() ![]() ![]() ![]() ![]() |
Well if you go on the Rockauto site and for example for a 68 AMX 390 they list an srk 100 drive and the picture shows 9 teeth the way I count them. Other than than I know nothing about how many teeth it should have.
|
|
![]() |
|
Trader ![]() AMC Addicted ![]() Joined: May/15/2018 Location: North America Status: Offline Points: 688 |
![]() ![]() ![]() ![]() ![]() |
AMC should be 9 tooth and you have to watch the engagement throw. AMC should be 0.930" - this is from memory so should be checked, some Ford's have only a 0.750" to 0.780" throw and will grind on an AMC every time.
Some suppliers are selling Ford starters (which the body and shaft are) as AMC's.
|
|
![]() |
|
billd ![]() Moderator Group ![]() ![]() Forum Administrator Joined: Jun/27/2007 Location: Iowa Status: Offline Points: 28365 |
![]() ![]() ![]() ![]() ![]() |
The piece the starter fork goes over is installed OPPOSITE the way they are on FORD.
Be careful - The piece I point to here is normally flipped on Ford (although there could be some ford that use this - I've not seen one personally) - this is the AMC way - I may have a couple I could grab part numbers from. DO NOT EVER BUY REMANUFACTURED drives. Please be sure they specific NEW. New is much more expensive but I have had a greater than 50% fail rate on reman drives so I stopped using them years ago - decades ago, in fact.
(I repair and restore AMC starters so try to have at least 3 or 4 correct new drives on hand for use on those I restore for others) ![]() |
|
![]() |
|
billd ![]() Moderator Group ![]() ![]() Forum Administrator Joined: Jun/27/2007 Location: Iowa Status: Offline Points: 28365 |
![]() ![]() ![]() ![]() ![]() |
You didn't say if it was a reman, or has been repaired, etc. - if it's an original AMC starter there will be a number in the starter frame. Later ones used a decal with the AMC number on it. Otherwise, if a reman, chances are it's made of Ford starter parts (meaning starters made for and installed on Fords) with "will fit AMC" type drive and end on it. If you have some numbers, I may be able to check as those starters for AMC had specific numbers cast into the drive end (the cast aluminum part) |
|
![]() |
|
ditdit ![]() Supporter of TheAMCForum ![]() ![]() Joined: Dec/30/2007 Location: South Carolina Status: Offline Points: 62 |
![]() ![]() ![]() ![]() ![]() |
thanks guys ,I will take the starter off of the AMX and get back to you all again tks
|
|
1968 AMX 401/727
1984 Eagle 4.0 org owner 1988 Eagle (time machine) 1980 Jeep J10 1977 Hornet AMX (Green)(sold) |
|
![]() |
|
mixed up ![]() AMC Addicted ![]() ![]() Joined: Jun/16/2015 Location: Monroe mich Status: Offline Points: 946 |
![]() ![]() ![]() ![]() ![]() |
believe it or not in my 290 4spd I used a 77 Fairmont 6cyl starter and had no issues with grinding I used it because of terminal location and header clearance
|
|
69 amx 290 auto
65 220 290 4spd 80 ford fairmont |
|
![]() |
|
ditdit ![]() Supporter of TheAMCForum ![]() ![]() Joined: Dec/30/2007 Location: South Carolina Status: Offline Points: 62 |
![]() ![]() ![]() ![]() ![]() |
thanks for the info .
jim
|
|
1968 AMX 401/727
1984 Eagle 4.0 org owner 1988 Eagle (time machine) 1980 Jeep J10 1977 Hornet AMX (Green)(sold) |
|
![]() |
Post Reply ![]() |
|
Tweet
|
Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |