Your donations help keep this valuable resource free and growing. Thank you.
|
Amc spirit swap too v8 ? |
Post Reply | Page 12> |
Author | |
austinsamx74
AMC Apprentice Joined: Nov/10/2016 Location: pa Status: Offline Points: 203 |
Post Options
Thanks(0)
Posted: Sep/14/2017 at 5:18pm |
I've been tossing the idea of building a spirit as my drag car in a few years I was wondering if a amc javelin v8 k member would work ?
|
|
gremlin1945
AMC Addicted Joined: May/21/2008 Location: new jersey Status: Offline Points: 781 |
Post Options
Thanks(0)
|
Nope. American,gremlin.hornet concord. In other words small car cross member.
|
|
former NHRA #1945
former IHRA #1945 T/SA |
|
austinsamx74
AMC Apprentice Joined: Nov/10/2016 Location: pa Status: Offline Points: 203 |
Post Options
Thanks(0)
|
Ok thanks
|
|
GreggR
AMC Addicted Joined: Aug/21/2009 Location: Painesville, OH Status: Offline Points: 1267 |
Post Options
Thanks(0)
|
Find Bulltear 6 to 8 engine mounts?
|
|
No matter where you go, there you are... Buckaroo Banzai.'75 Hornet Hatchback
|
|
gremlin1945
AMC Addicted Joined: May/21/2008 Location: new jersey Status: Offline Points: 781 |
Post Options
Thanks(0)
|
The Bulltear mounts are fine if you have welding and fabrication skills. If you're going to farm the work out it's better to wait on a small car cross member and plates. Just my .02 cents.
Edited by gremlin1945 - Sep/16/2017 at 8:05pm |
|
former NHRA #1945
former IHRA #1945 T/SA |
|
austinsamx74
AMC Apprentice Joined: Nov/10/2016 Location: pa Status: Offline Points: 203 |
Post Options
Thanks(0)
|
Ok ill checkout bulltear thanks for input guys
|
|
austinsamx74
AMC Apprentice Joined: Nov/10/2016 Location: pa Status: Offline Points: 203 |
Post Options
Thanks(0)
|
I did checkout there web site did a search and found only one item and it said amc 6 too 8 motor motors that's all they said.didn't say for concord spirit etc
|
|
AMC instigator
AMC Addicted Joined: Sep/13/2009 Location: Cook Minn. Status: Offline Points: 1265 |
Post Options
Thanks(0)
|
The ones listed are the ones you want, they fit many car models. Might be best to call there about them. The other option is to purchase a factory v-8 crossmember and the engine block plates [mounts], at a larger cost. Both ways will work. Spirits make great race cars! SH
Edited by AMC instigator - Sep/15/2017 at 9:27pm |
|
AMC RACES event coordinator
Former NAMDRA Vice President- NAMDRA-#2398 AMO-#8370 Northstar AMC Club-#9 |
|
gremlin1945
AMC Addicted Joined: May/21/2008 Location: new jersey Status: Offline Points: 781 |
Post Options
Thanks(0)
|
Let me rephrase my post. Do you have any welding experience? These mounts have to be engineered to lay in the engine compartment at the right location for engine clearance, correct height for exhaust clearance, transmission mounting. If you've never done work like this wait till you find the correct small car cross member setup.
|
|
former NHRA #1945
former IHRA #1945 T/SA |
|
austinsamx74
AMC Apprentice Joined: Nov/10/2016 Location: pa Status: Offline Points: 203 |
Post Options
Thanks(0)
|
I think I can do it I'm a auto body tech with 15 years in it and weld every week . but I've never made a engine fit anything. I imagine there be some test fiting like engine tranny. Have too get drive shaft made. Would have too find a amc 20 rear that would fit . I have javelin but I would quess there way too wide
|
|
Post Reply | Page 12> |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |