Your donations help keep this valuable resource free and growing. Thank you.
|
AMC 360 TBI INJECTORS for 4.3 |
Post Reply | Page 12> |
Author | |
GDAWG1007
AMC Apprentice Joined: Jun/29/2013 Location: Savannah, GA Status: Offline Points: 79 |
Post Options
Thanks(0)
Posted: Jun/28/2020 at 7:49pm |
I have installed an AMC 360 V8 in my 1979 CJ-5 Jeep. My issue is with the injectors. I installed a 4.3 V6 TBI in a 258 Inline 6 that through a rod so I bought a AMC 360 engine and put the 4.3 TBI in it, but the 4.3 injectors are for the in-line 6 so would anyone know if I can put V8 injectors into the 4.3 TBI? If so, do I need to do anything else? Thanks for the assistance.
|
|
1979 CJ-5 Renegade AMC 360, T-176, Dana 300, One Piece AMC 20 Axle 4:10 Gears, Dana 30 4:10 Gears, etc
|
|
Heavy 488
AMC Addicted Joined: Apr/27/2019 Location: In the Status: Offline Points: 3553 |
Post Options
Thanks(0)
|
I believe there's about 4 different injector sizes to choose from depending on application. Who programmed the chip?
Edited by Heavy 488 - Jun/28/2020 at 8:20pm |
|
GDAWG1007
AMC Apprentice Joined: Jun/29/2013 Location: Savannah, GA Status: Offline Points: 79 |
Post Options
Thanks(0)
|
The chip I believe is still a in line 6 chip for the TBI so I guess I should switch that out as well. Howell TBI kit from 4 wheel Drive
|
|
1979 CJ-5 Renegade AMC 360, T-176, Dana 300, One Piece AMC 20 Axle 4:10 Gears, Dana 30 4:10 Gears, etc
|
|
Heavy 488
AMC Addicted Joined: Apr/27/2019 Location: In the Status: Offline Points: 3553 |
Post Options
Thanks(0)
|
Check with them. They need to set the PWM to match the injector flow rate.
|
|
GDAWG1007
AMC Apprentice Joined: Jun/29/2013 Location: Savannah, GA Status: Offline Points: 79 |
Post Options
Thanks(0)
|
So I went bank through my notes from 10 years ago and found that I did buy the V8 chip for the TBI but did not replace the 4.3 injectors. Now I am looking for a 5.7 to 5.9 injectors for the AMC 360. I’m thinking I’ll go with the 5.7 once I found a set.
|
|
1979 CJ-5 Renegade AMC 360, T-176, Dana 300, One Piece AMC 20 Axle 4:10 Gears, Dana 30 4:10 Gears, etc
|
|
1982AMCConcord
AMC Addicted Joined: Jul/13/2012 Location: Kenosha, WI Status: Offline Points: 1287 |
Post Options
Thanks(0)
|
Yes.. you will need the TBI 350 68lb/hr injectors for a 360. You could potentially use the 55lb/hr. one at higher pressure but I would not recommend that route as it could still run lean on the top end if you start pushing too much hp. The Chevy Caprice 9C1 68lb/hr injectors would be ideal for you. Check ebay... maybe Rock Auto.
|
|
GDAWG1007
AMC Apprentice Joined: Jun/29/2013 Location: Savannah, GA Status: Offline Points: 79 |
Post Options
Thanks(0)
|
So looking online last night and not wanting to wait two weeks to get OEM 350 injectors I decided to buy police special 350 injectors. Now the site recommends using an adjustable fuel regulator which judging but the TBI I have I’ll need to drill a hole for the adjustment screw or screwdriver to fit up into. Was thinking of getting one with a gauge but really not sure how that would work with getting the ones I’ve seen online to fit on the TBI since there really isn’t much room for the fuel regulator to be installed on the TBI.
|
|
1979 CJ-5 Renegade AMC 360, T-176, Dana 300, One Piece AMC 20 Axle 4:10 Gears, Dana 30 4:10 Gears, etc
|
|
1982AMCConcord
AMC Addicted Joined: Jul/13/2012 Location: Kenosha, WI Status: Offline Points: 1287 |
Post Options
Thanks(0)
|
You might find some of the products offered by CFM Technologies helpful... Yes... A FPR is going to be in your best interest. I would look for one that's vacuum referenced... They are well suited for fuel injection applications... But more expensive....
|
|
Halvard
AMC Apprentice Joined: Jan/13/2020 Location: Norway Status: Offline Points: 45 |
Post Options
Thanks(0)
|
What kind of time and cost is involved with getting this up and running?
Summit brand EFI (produced by Fitech I heard) is down to $750 now, not including fuel pump, which you probably already have... |
|
Halvard
Jeep CJ-7 AMC401 SM465 |
|
GDAWG1007
AMC Apprentice Joined: Jun/29/2013 Location: Savannah, GA Status: Offline Points: 79 |
Post Options
Thanks(0)
|
I’ll take a look at the link as I’m looking on Jegs right now but not really finding much.
As far as time and money set up goes the TBI I have was organically for my 258 inline 6, but when I replaced that engine I bought a AMC 360. I replaced the chip in the computer with a 304-390 set up chip, but did not replace the injectors. So now I just ordered these police special 350 injectors 12.5 to 15psi. My fuel pump is a Walbro GSL395 Fuel Pump that runs at 15psi and below. I bought this fuel regulator plate to block off the current fuel regulator location and now need to buy an external fuel pump but most I am finding have threaded inlets that I guess will need to change out to braided ones all the way to the fuel pump (5ft).
|
|
1979 CJ-5 Renegade AMC 360, T-176, Dana 300, One Piece AMC 20 Axle 4:10 Gears, Dana 30 4:10 Gears, etc
|
|
Post Reply | Page 12> |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |