Your donations help keep this valuable resource free and growing. Thank you.
|
1969 AMX Tach - Driving me crazy |
Post Reply | Page 123> |
Author | |
musictoyz
AMC Nut Joined: Apr/17/2012 Location: cumberland, me Status: Offline Points: 377 |
Post Options
Thanks(0)
Posted: Jun/17/2018 at 8:33pm |
1969 AMC AMX 390 Tach - Auto - All Stock Tach turns on mmm every 5th or 6th trip I pulled the dash off, ran a new wiring harness around the window to test. Before I pulled all the wires out of the bay....no tach the car runs....if I disconnect the old wires or the new wires...engine dies. either set of wires...no tach... Butttttt the tach does work ? just once every 3 months ? IS there a ground I am missing ? ALL GUAGES WORK BESIDES THIS
|
|
1969 BBG,BBO, BBB/ 1970 Machine - www.bigbadamx.com
|
|
amcglass
AMC Addicted Joined: Dec/11/2011 Location: NW Ohio Status: Offline Points: 2588 |
Post Options
Thanks(0)
|
would think it is a ground issue
|
|
Javmanpres
BBG Mark Donohue 401 74 Jav/AMX 71 Matador 2dr sedan delivery wagon 1902 Rambler Runabout 70 T/A Javelin |
|
mmaher94087
AMC Addicted Joined: Apr/01/2008 Location: Arizona Status: Offline Points: 1690 |
Post Options
Thanks(0)
|
Yes. Sounds like a ground issue. The '69 tach built into the cluster will allow one to drive the car even if the tach is burned out. The '68 Tach will not. Check your grounds for the cluster.
|
|
Mike
|
|
Trader
AMC Addicted Joined: May/15/2018 Location: Ontario Status: Offline Points: 6909 |
Post Options
Thanks(0)
|
After checking the grounds, with the engine running, put your hand up and give the main instrument harness connector a wiggle and see if anything changes.
Don't have the rally cluster but mine did have a board pin loose in the cluster. Intermittent on off gas and temperature gauge from the same power supply. Had to take the board out and solder the pin to the board to ensure good electrical connection - did all of them since I was in there.
|
|
musictoyz
AMC Nut Joined: Apr/17/2012 Location: cumberland, me Status: Offline Points: 377 |
Post Options
Thanks(0)
|
Trader....I am pretty sure the 69 run totally on its own 2 wire harness...you are correct that pin connector can give you a bunch of headache...
I took the cluster out...I took the tach out...and open it. Yes thats how tired I am of this....the tach has a mini transformer to knock the 12 v down ...there is 4 caps, 2 resistors and a magnetic thing that is connected to the dial.. looked around... cleaned terminals... hooked it...it works But it jumps all over... So I think I am gonna call a tach guy tomorrow...see how much, if crazy $ may put in new caps etc
|
|
1969 BBG,BBO, BBB/ 1970 Machine - www.bigbadamx.com
|
|
Rebel Machine
AMC Addicted Joined: Jul/03/2007 Location: Western Il Status: Offline Points: 5121 |
Post Options
Thanks(0)
|
You are correct, the AMX tach does not use a ground. It's inline with the power feeding the ignition coil. I'd think if there was an intermittent connection you'd have a misfiring engine. -Steve-
|
|
Trader
AMC Addicted Joined: May/15/2018 Location: Ontario Status: Offline Points: 6909 |
Post Options
Thanks(0)
|
Yes the tach has a separate connection - my mistake. Just finished a Ford that had an intermittent tach and put that together with the 69 Javelin temperature/gas gauge problem.
Too many vehicles with intermittent electrical faults in the last few months! Including the brain. |
|
musictoyz
AMC Nut Joined: Apr/17/2012 Location: cumberland, me Status: Offline Points: 377 |
Post Options
Thanks(0)
|
I know and they can drive this old brain crazy !
|
|
1969 BBG,BBO, BBB/ 1970 Machine - www.bigbadamx.com
|
|
musictoyz
AMC Nut Joined: Apr/17/2012 Location: cumberland, me Status: Offline Points: 377 |
Post Options
Thanks(0)
|
Welllllllll it seems I didn't even know the addition of Pertronixs II would create such havoc.... Anyone know of the conversion to the tach for Pertronixs...everyone wants $299 for this repair/convert yikes ! |
|
1969 BBG,BBO, BBB/ 1970 Machine - www.bigbadamx.com
|
|
PHAT69AMX
AMC Addicted Joined: Jul/07/2007 Location: West Virginia Status: Offline Points: 5926 |
Post Options
Thanks(0)
|
Don't know what it takes when using PerTronix...
But when I used a UniLite and an MSD Box, this is what it took to make stock tach work... |
|
Post Reply | Page 123> |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |